Climax VM1350 Скачать руководство пользователя страница 50

Страница: 50 / 98

Page 38

VM1350-1500-1600 Operating Manual

NOTICE

The air supply line must always offer an air pressure of 6,3 bar to
the maintenance unit.

The air supplied to the maintenance unit must be free from
humidity and other particles to protect the machine against
damages.

All air supply lines, fittings, etc. must be provided according to
the air pressure and volume requirements.

The grinding pressure can be adjusted during machining operation as required.

For lapping operation, make sure that sufficient lapping paste is put onto the sur-
face to be machined.

For grinding operation, make sure that the abrasive is still in proper condition.
Always change abrasives in time, otherwise it will result in poor performance.

Over proportional heat creation of abrasive might result into shearing off and the
valve seat might be damaged.

4.4

HANGE OF ABRASIVES

Stop the machine with trigger button (electric drive) or with red safety button on
maintenance unit (pneumatic drive)

•

Release grinding pressure. To release grinding pressure, use the star
knob of the tilting adapter.

•

Disconnect machine from power supply

•

Hold machine arm and open the flap of the tilting adapter

•

Take the machine arm with the bracket out of the ball locations. Be
careful - avoid any collision between tool and valve body

•

Put the machine arm into a stable position to change the abrasive

•

Change the abrasive

•

Put machine back into position, adjust grinding pressure and go on with
the grinding operation (steps vice versa as described above)

Содержание VM1350



































































































Результаты поиска

Содержание VM1350

Отзывы:

Похожие инструкции для VM1350

Бренды по названию

Популярные бренды

Climax VM1350, Руководство по эксплуатации

Результаты поиска

Содержание VM1350

Отзывы:

Похожие инструкции для VM1350

Бренды по названию

Популярные бренды