Climax VM1350 Скачать руководство пользователя страница 54

Страница: 54 / 98

Page 42

VM1350-1500-1600 Operating Manual

Table 5-1 lists maintenance intervals and tasks

5.2

PPROVED LUBRICANTS

CLIMAX recommends using the following lubricants at the locations indicated.
Failure to use the appropriate lubricants can result in damage and premature
machine wear.

CAUTION

Avoid damage, premature machine wear, and protect your
warranty by using only approved lubricants.

5.3

UBRICATING THE MACHINE MODULES

Most of the machine components are maintenance-free.

ABLE

5-1. M

AINTENANCE INTERVALS AND TASKS

Interval

Task

Reference

Before each use

Lubricate the ball joint coupling of the machine spindle with grease.

Check power supply lines for visible damages.

Check the maintenance unit (with pneumatic drive).

Check the ventilating slots of electric drive motor

Before and after each
use

Clean the machine and check for visible damage.

After 150 hours

Disassemble, clamp, clean, and lubricate the gear of the pneumatic
drive motor with Bosch-special grease.

Section
5.3.1

After 300 hours

Inspect the drive chain integrated in the machine arm and the upper
gear.

Section
5.3.2

Lubricate the drive chain and upper gear.

ABLE

5-2. A

PPROVED LUBRICANTS

Application Area

Lubricant

Frequency

Ball joint

Dow Corning Molykote G-N

Each use

Pneumatic drive gear

CASTROL MOLUB-Alloy 6040/150

Yearly

Chain drive

CASTROL Chain Oil 22

Yearly

Upper gear

CASTROL MOLUB-Alloy 6040/150

Pneumatic motor

CASTROL Hyspin AWS-32

A/R 6 oz

Long-term storage

LPS Labs LPS-3

6 months

Содержание VM1350



































































































Результаты поиска

Содержание VM1350

Отзывы:

Похожие инструкции для VM1350

Бренды по названию

Популярные бренды

Climax VM1350, Руководство по эксплуатации

Результаты поиска

Содержание VM1350

Отзывы:

Похожие инструкции для VM1350

Бренды по названию

Популярные бренды