Page 52
LM5200 Operating Manual
Parallel Setup
Option 1
1. Move the ram to one end of the bed, and mount a dial indicator between the ram and the
gantry rail as shown in Figure 14.
Figure 21
2. Use the feed motor on the bed to drive the ram from one end of the bed to the other.
Adjust the gantry side of the bed as you go and align with the drive side so that the rails
are parallel within 0.002 inch.
3. Repeat until there is no more adjustment needed, and then tighten down the bed and
ram clamps on the gantry side.
IMPORTANT
When changing direction there may be significant movement of the
indicator as the machine loads to move in the opposite direction.
Option 2
1. Remove the feed motor from the drive side of the bed.
2. Manually push the ram along the full length of the bed several times while tightening
down the gantry side as you go.
3. Use a precision leveling tool and a dial indicator, as described previously, to check for
spots that are out of alignment. Make adjustments as necessary.
4. Tighten down the ram clamps on the gantry side when no more adjustment is needed.
When complete, the ram should glide smoothly along the full length of the bed. A tight spot
indicates an area that is out of alignment.
Содержание LM5200
