5
For Normal Wrist Transmitters
(WTR-) or Fall Sensor
1. Press and hold the
RESET
button of
CTC1041RV for 6 seconds until you hear
the double beep and followed by a long
beep.
2.
The RED LED starts flashing. CTC-
1041RV is now in the learning mode.
3.
Press and both the
HELP
and
Pendant
#1 (WTR- Series or Fall Sensor)
buttons
simultaneously until CTC-1041RV emits a
double-beep.
4.
Pendant
#2
has
been
learnt-in
successfully.
5.
Press the Reset & Help button at the
same time to exit the learning mode. The
RED LED will dim to indicate that the
system is back to idle mode.
2.3. Learning in DECT Devices
(CTC-808RV, CP-23 and
WTRVS)
CTC-1041RV can learn in 4 DECT devices
at most. The DECT devices will be
automatically assigned to Zone 1~Zone 10
except Zone 3.
Learning in CTC-808RV
1. Press and hold the green reset
button of
CTC-1041RV for 6 seconds until you hear
two beeps followed by a long beep.
2. The red LED starts flashing. CTC-1041RV
is now in learning mode.
<
<
N
N
O
O
T
T
E
E
>
>
CTC-1041RV can learn in 4 DECT
devices at most. If fewer than 4 DECT
devices have been learned into CTC-
1041RV, the red LED will flash slowly to
indicate there are still empty zones for
DECT devices. If CTC-1041RV has
learned 4 DECT devices and there are no
more zones for DECT devices, the red
LED will flash quickly.
You can clear Zone 1 and Zone 2 for
DECT devices to be learned in by
pressing and holding CTC-1041RV’s
green reset button for 6 seconds until you
hear a long beep that indicates the
devices in Zone 1 and Zone 2 have been
simultaneously removed. Now you can
learn DECT devices into Zone 1 and Zone
2.
The above method, however, cannot
create available zones for more DECT
devices if CTC-1041RV has already
learned in 4 DECT devices and none of
them are in Zone 1 or Zone 2.
3. Press and hold CTC-808RV’s learning
button for 5 seconds until you hear 2
beeps. Release the button and CTC-
808RV will emit one short beep to indicate
it is now in learning mode. The green LED
of CTC-808RV is turned on.
4. When CTC-808RV is successfully learned
in, both CTC-1041RV and CTC-808RV will
emit two beeps to indicate the successful
learning. The green LED on CTC-808RV
will be turned off.
<
<
N
N
O
O
T
T
E
E
>
>
If you do not hear the two beeps and if
CTC-808RV emits one short beep and its
green LED is off and red LED steady on,
that means the learning process has
failed. Please repeat the learning steps
again.
5. Check if CTC-808RV has been learned in
successfully. Press the HELP button on
CTC-808RV and you will hear continuous
beeps from CTC-808RV. When CTC-
808RV beeps, the CTC-1041RV will
respond with 1 beep to indicate that CTC-
808RV is within the operation range.
6. Press the reset and help buttons at the
same time to exit learning mode. The red
LED will dim to indicate that CTC-1041RV
is back to idle mode.
Learning in CP-23 or WTRVS
1. Press and hold the green reset
button of
CTC-1041RV for 6 seconds until you hear
two beeps followed by a long beep.
2. The red LED starts flashing. CTC-1041RV
is now in learning mode.
<
<
N
N
O
O
T
T
E
E
>
>
CTC-1041RV can learn in 4 DECT
devices at most. If fewer than 4 DECT
devices have been learned into CTC-
1041RV, the red LED will flash slowly to
Содержание CTC-1041RV
Страница 1: ...c August 12 2013 ...
