Climax CTC-1041RV Скачать руководство пользователя страница 24

Страница: 24 / 37

4.1.2. Non-Emergency Speech Call

This function is only available when
Command #7 is programmed.

Making a Non-Emergency Call from CTC-
1041RV

Step 1.

From Idle mode, press and hold

the

RESET

button for 3 seconds until

CTC-1041RV emits a short beep.

Step 2.

Release the button and

one short

beep

will sound. CTC-1041RV dials

the

phone

number

entered

Command #7.

Making a Non-Emergency Call from CTC-
808RV

Step 1.

Hold the green Service button on

CTC-808RV for 5 seconds. CTC-
808RV will emit a short beep.

Step 2.

CTC-1041RV will dial the phone

number  programmed  via  Command
#7.  The  dial  done  can  be  heard  on
CTC-808RV.

Step 3.

When the call gets through, CTC-

808RV will open two-way voice
communication.

When  5  short  beeps  (warning  beeps)
sound    instead  of  a  short  beep,  it  means
CTC-1041RV  is  not  in  idle  mode  and  it  is
not  allowed  to  use  non-emergency  call
function.

If a non-emergency call is made from
CTC-1041RV, two-way communication will
be conducted via CTC-1041RV.

If  a  non-emergency  call  is  made  from
CTC-808RV,  two-way  communication  can
be  conducted  via  all  CTC-808RVs  in  the
system.

Step 3.

the

dialing

succeeds,

CTC-

1041RV will open a two-way voice
communication

between

the

call

recipient and CTC-1041RV for 1 to 10
minutes (set by Command 46).

The Red button backlight will illuminate
during the communication.

If the dialing fails, CTC-1041RV will not
retry.

Press Reset button can stop and cancel
the dialing & call at any time.

Step 4.

At the last 20 & 10 sec, CTC-

1041RV

will emit two beeps via the telephone
handset to alert the call recipient. If the
Call

Recipient

needs

conversation time, press any DTMF
key (except 9) can add another 1 to 10
minutes (set by Command 46).

Step 5.

Press  DTMF  9  or  Reset  button  to
terminate  the  call.  The  Red  button
backlight  dims  and  CTC-1041RV
returns to idle mode.

4.1.3. AC Power Check Up

If the AC Power failure is detected for 10
seconds or longer, the GREEN LED starts
to flash as a visual warning to the user.

Once the AC Power resumes, the GREEN
LED turns steady on again.

If  the  AC  Power  failure  lasts  for  an  hour,
CTC-1041RV  will  send  an  AC  Failure
report to the Monitoring Center.

After the Power restoration lasts more
than one hour, CTC-1041RV will report AC
Restore to the Monitoring Center.

4.1.4. CTC-1041RV Low Battery

CTC-1041RV  is  unable  to  detect  its
Battery  condition  at  first  30  minutes  after
powering up.

When the battery low condition lasts for

4 -

6 mins

, CTC-1041RV will report to the

Monitoring Center and the GREEN LED
flashes slowly.

If Low Battery condition persists, CTC-
1041RV will emit 2 short beeps every hour.

Press the

RESET

button to clear the

warning beeps, and the LED returns to
steady ON.

After the battery voltage is restored and
lasts for 12 hours, CTC-1041RV will send

Battery Restore

report to Monitoring

Center and the GREEN LED returns to
steady ON.

4.1.5.

CTC-1041RV

Battery

Disconnection

CTC-1041RV can detect the absence of

Содержание CTC-1041RV






































Результаты поиска

Содержание CTC-1041RV

Отзывы:

Похожие инструкции для CTC-1041RV

Бренды по названию

Популярные бренды

Climax CTC-1041RV, Руководство пользователя

Результаты поиска

Содержание CTC-1041RV

Отзывы:

Похожие инструкции для CTC-1041RV

Бренды по названию

Популярные бренды