background image

Installation Manual 

97B0055N03

Rev.: 2/4/13

ATC32U01 iGate

 Communicating, 

Programmable Thermostat

Table of Contents

Section Title 

Page

  

Safety/Installation 

Considerations  3

1.0 

User Menu Settings 

  4

2.0 

Installer Menu Settings 

  6

 

2.1 

Installer Menu Settings Access 

  6

 2.2 

Thermostat 

Confi guration 

  6

3.0 System 

Confi guration 

  7

 3.1 

Airfl ow Selection 

  7

 3.2 

Option 

Selection 

 7

 3.3 

Unit 

Confi guration 

  8

 

3.4  

Pump Confi guration 

  8

 3.5 

Valve 

Confi guration 

  9

 3.6 

Multi-Unit 

Confi guration 

  9

4.0 Accessory 

Confi guration 

  10

 

4.1  

Air Filter 

  10

 4.2 

 

Humidifi er 

  10

 

4.3  

UV Lamp 

  10

Caution:

These instructions are intended to be used by the installer or service personnel.  End users are NOT advised to change or 
modify any of these settings.  Doing so may cause the equipment to stop working properly and/or may void the warranty on 
both the thermostat and the equipment.

Section Title 

Page

 

4.4  

Air Cleaner 

  10

5.0 

Input Dealer Information 

  11

6.0 Humidity 

Confi guration 

  11

7.0 Temperature 

Algorithm 

 

11

8.0 

Demand Reduction Confi guration    11

9.0 Service 

Mode 

 

12

 9.1 

Manual 

Operation 

 12

 9.2 

Control 

Diagnostics 

 12

 9.3 

Dipswitch 

Confi guration 

  13

 9.4 

Fault 

History 

 13

 

9.5 

Clear Fault History 

  14

 9.6 

Multi-Unit 

Diagnostics 

 14

 

9.7 

Multi-Unit Fault Information 

  15

10.0 Restore 

Defaults 

 

15

11.0 Revision 

History 

16

Содержание ATC32U01 iGate

















Отзывы: