Clemas & Co Tennant GL20 Скачать руководство пользователя

Страница: 19 / 57

OPERATION

Tennant T300 (03- 2015)

6. Press the Zone Setting numbers for quick

operation (Figure 42). The three preset zones are

factory configured with different solution flow rates

and down pressures.

FIG. 42

To change the Zone Settings for a specific

scrubbing application, configure the new zone

settings and press and hold the zone button until it

blinks three times to save new zone setting.
The zone settings can configure the following

controls:
- Down pressure rate

- Solution flow rate
- Quiet-Mode on or off (option)
- ec-H2O mode on or off (option)
- Severe Environment mode on or off (option).

NOTE: The severe environment mode and ec-H2O

mode cannot be configured together.

7. If a machine fault is detected during operation, the

service indicator will light up and begin flashing

(Figure 43). See SERVICE INDICATOR CODES.
If the ec-H2O system detects a fault during

operation, the ec-H2O icon will turn or blink red.

See SERVICE INDICATOR CODES.

FIG. 43

ec-H2O INDICATOR

CONDITION

Solid blue

Normal operation

Blinking blue/red

Water conditioning cartridge

expired. Replace cartridge.

Solid or blinking red

See Service Indicator Codes.

T300 MODEL WITH PRO-PANEL CONTROLS

There are two types of user modes that will interface

with the operator home screen:

Operator Mode -

Capable of machine operation with

permissions and restrictions controlled by the

supervisor.

Supervisor Mode -

Capable of machine operation

with full use of all controls, along with configuring

permissions and restrictions for the operator mode.
A new machine from the factory will automatically start

up in the supervisor mode by default. To configure the

control panel with permissions and restrictions for the

operator mode, see SUPERVISOR CONTROLS

instructions at back of manual.
1. Turn the key to on ( I ) position. At start up, a

Tennant logo screen will first appear followed by the

operator home screen as shown below (Figure 44).

FIG. 44

Models equipped with the ec-H2O option, the ec-H2O

icon will appear at the center of the display. This

indicates the ec-H2O system is turned on and ready for

operation. The ec-H2O system will automatically turn

on at start up.
To turn off the ec-H2O system, press the ec-H2O on/off

switch located below the key switch. A slash mark over

the icon will indicate that the ec-H2O system is turned

off (Figure 45).

FIG. 45

Содержание Tennant GL20


























































Результаты поиска

Содержание Tennant GL20

Отзывы:

Похожие инструкции для Tennant GL20

Бренды по названию

Популярные бренды

Clemas & Co Tennant GL20, Руководство оператора

Результаты поиска

Содержание Tennant GL20

Отзывы:

Похожие инструкции для Tennant GL20

Бренды по названию

Популярные бренды