manualshive.com logo in svg

ClearSpan SunBurst Dome Premium Gothic Style 106602, Руководство по сборке

Поделиться
Скачать
ClearSpan SunBurst Dome Premium Gothic Style 106602 Скачать руководство пользователя страница 19

Visit 

www.ClearSpan.com

 for additional products and customer assistance.

CLEARSPAN

™

 SUNBURST POLY BUILDINGS

1

Thread the D-ring strap through the slit in the cover 
pocket, wrap it around the cover conduit, and attach 
the strap assembly to the rafter.  

8.

NOTE:

 Verify that the cover is centered side-to-side 

before attaching the D-ring straps.

Repeat the steps for the remaining D-ring straps. 
 

NOTE:

 D-ring straps are attached to one side of the 

shelter. Ratchets are attached directly across from the 
D-ring straps on the 

same rafter assembly

.

Move to the other side of the shelter and attach the 
ratchets to the rafters. Use the cover conduit as a guide 
to attach the ratchets to the rafters at the proper height. 
Fasten ratchets to the outside of these rafters using a 
Tek screw.

9.

10.

As previously described, make a slit in the cover 
conduit pocket and insert a 3' section of plain strap 
through the slit and around the cover conduit.

11.

ATTACH MAIN COVER (CONTINUED)

Thread the plain strap ends into the ratchet and slightly 
tighten. 
 

NOTE:

 It may be necessary to remove excess strap if it 

binds up in the ratchet.

12.

Repeat the steps for the remaining ratchet or ratchets.

Using additional help (if needed) tighten the main cover 
beginning with the ratchets along the side of the shelter 
frame.

After the side ratchets are tightened, return to the front 
and back end ratchets and tighten. 
 

NOTE:

 Loosen the ratchets if needed to remove 

excess strap and tighten. If the main cover is not 
centered as desired, the D-rings straps can be 
repositioned (higher or lower) as needed and the main 
cover retightened.

Fold the skirt of main cover down and over the ratchets 
and D-ring straps to complete the installation of the 
main cover. 

Read the care and maintenance information that 
follows.

13.

14.

15.

16.

17.

Содержание SunBurst Dome Premium Gothic Style 106602






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды