manualshive.com logo in svg

ClearSpan SunBurst Dome Premium Gothic Style 106602, Руководство по сборке

Поделиться
Скачать
ClearSpan SunBurst Dome Premium Gothic Style 106602 Скачать руководство пользователя страница 18

Visit 

www.ClearSpan.com

 for additional products and customer assistance.

CLEARSPAN

™

 SUNBURST POLY BUILDINGS

1

On the side of the shelter where the D-ring straps are 
located, lift the main cover skirt and cut a slit through 
the main cover pocket at the rafters identified by the 
arrows above.

6.

Once the main cover is pulled into position, center the 
cover on the frame and remove the ropes. Loosely 
secure the ends of the cover to the ratchets attached to 
the front and back end panel conduits. 
 

ATTENTION:

 Do not tighten the straps at this time

Place the D-ring straps on the ground along one side 
of the shelter beside the rafters identified by the arrows 
below. Place the plain straps and ratchets 

on the 

opposite side of the shelter

 at the same rafters as the 

D-ring straps. 

4.

5.

ATTACH MAIN COVER

Gather the parts:

Main cover (with conduits already inserted)

Ropes long enough to reach over the frame (provided 
by customer)

Ratchets  

D-ring straps and plain straps

Tek screws

Box cutter or utility knife 

Assembly Procedure

To pull the cover over the frame, attach a rope to each 
end of the cover conduit. Wrap the rope around the 
conduit a few times to prevent it from slipping off. 

•

•

•

•

•

•

1.

 

NOTE:

 Depending on the length of the cover it may 

be necessary to attach additional ropes to the cover 
conduit between the end ropes by cutting a small 
opening in the cover pocket and tying the rope around 
the conduit. DO NOT cut through the main cover. 

Cut 

through the conduit pocket only.

With all ropes attached to the cover conduit, lift the 
conduit and carry the cover toward the base of the 
frame.

Toss the ropes over the frame and pull the cover into 
position. One person is required at each rope. 

2.

3.

NOTE:

 Shelter shown above may be a different model. 

Drawing is used for illustration purposes only.

Cover 
Conduit

Ropes

Verify that the cover is centered on the frame side-to-
side and end-to-end.

7.

NOTE:

 Diagram above is an example of the 16' shelter. 

Consult the Side Profile diagrams in the Quick Start 
section for your frame.

Ground Level

Содержание SunBurst Dome Premium Gothic Style 106602






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды