manualshive.com logo in svg

ClearSpan SunBurst Dome Premium Gothic Style 106602, Руководство по сборке

Поделиться
Скачать
ClearSpan SunBurst Dome Premium Gothic Style 106602 Скачать руководство пользователя страница 17

Visit 

www.ClearSpan.com

 for additional products and customer assistance.

CLEARSPAN

™

 SUNBURST POLY BUILDINGS

1

PREPARE MAIN COVER

Gather the parts:

Ratchets 

Pipe 1.315'' x 75'' swaged

Pipe 1.315'' x XX'' plain 

Cover 

Tek Screws 

Assembly Procedure
  
The main cover is attached to one side of the shelter using 
D-ring straps. It is stretched and secured to the remaining 
side with straps and ratchets.

The ends (front and back) are secured to the bottom of 
each end panel corner with a ratchet attached to the base 
rail. The straps to secure the ends of the main cover come 
pre-installed.

NOTE: 

When handling the main cover and setting it in 

position, 

do not pull on the end straps

. They will pull out of 

the cover.

WARNING: 

To prevent damage to the cover and to 

prevent serious personal injury, DO NOT attempt to 
install the main cover on windy days.

Fasten a ratchet to the base rail with a Tek screw in the 
bottom hole of the ratchet as shown below. Position the 
ratchet about 6'' in from the end rafter leg. Repeat this 
step at the remaining corners.

•

•

•

•

•

1.

Assemble two main cover conduits. Start each conduit 
assembly with one plain pipe and add swaged pipes to 
arrive at the correct length. 

This conduit is identical to 

the purlins that are attached to the frame.  

2.

NOTE:

 Duct tape (supplied by customer) Tek screws to 

prevent damage to main cover.  
 
These cover conduits are inserted into the pockets 
sewn into the main cover. The conduits are used to 
tighten and secure the main cover.

After assembling the cover conduits, locate the main 
cover and unfold it on a clean, smooth surface near the 
frame.  
 

NOTE:

 Unfold the main cover with the inside surface 

facing up.

Locate the cover ends with strapping and align with the 
front and back of the shelter.

Insert the cover conduits into the pockets of the main 
cover.  

3.

4.

5.

NOTE:

 Shelter shown above may be a different model. 

Drawing is used for illustration purposes only.

Cover Conduits

Cover 
Ends w/
Strapping

Locate all sections of pipe needed to assemble 
the cover conduit.

Insert the swaged end of each pipe into the 
plain end of another pipe until the conduit is 
assembled.

Secure each pipe joint with a Tek screw.

a.

b.

c.

End Panel

Ratchet

Tek Screw

6"

End Rafter Leg

Содержание SunBurst Dome Premium Gothic Style 106602






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды