manualshive.com logo in svg

ClearSpan SunBurst Dome Premium Gothic Style 106602, Руководство по сборке

Поделиться
Скачать
ClearSpan SunBurst Dome Premium Gothic Style 106602 Скачать руководство пользователя страница 15

Visit 

www.ClearSpan.com

 for additional products and customer assistance.

CLEARSPAN

™

 SUNBURST POLY BUILDINGS

1

ATTACH END PANELS 

CAUTION:

 To prevent damage, do not install end

panels on a windy day. 

Gather the parts:

End panels 

Fabric clips #CC6213 (Divide the quantity in half. Half 
is used for each end panel installation.)

Tek screws (#FA4482B)

FAMF01B fender washers: (

Set four (4) washers aside

 

for main cover installation and divide the remaining 
quantity in half. Half is used for each end panel.)

Measuring tape and utility knife 

Assembly Procedure

Spread an end panel out on the ground at the desired 
end of the frame and center the end panel as needed.

With the proper lift (or ladders) positioned inside the 
frame, pull the end panel up and over the top of the 
end rafter.

Verify that the panel is at the desired height

 and secure 

the end panel to the backside of the end rafter at the 
top, center position using a fabric clip and Tek screw. 
 

NOTE: 

Use the zippered door openings as guides 

when positioning the panel on the end rafter so that the 
panel is installed at the proper height.

•

•

•

•

•

1.

2.

3.

Moving outward in both directions, continue attaching  
fabric clips to secure the end panel to the rafter. 

Evenly 

space the fabric clips and work toward the ground. 
 
NOTE: 

Keep the panel stretched during this step to 

reduce wrinkles in the panel. 

Do not over stretch the 

panel. End panel shown may differ from actual panel.

4.

With the base rail loosely attached, pull the bottom 
edge of the end panel under the base rail. Verify that 
the door entrance remains accessible (if applicable).

With the end panel edge pulled into position, tighen the 
band clamps to secure the base rail to the frame. Also, 
install a Tek screw through each band clamp to secure 
the clamp to the ground post.

On the inside of the frame, pull the end panel edge 
around the base rail. Trim the panel as needed to wrap 
evenly around the base rail and the end rafter legs. 

5.

6.

7.

Attach the end panel to the top of the base rail using 
Tek screws and fender washers. DO NOT attach door 
opening to the base rail. (May not apply to all end panel 
designs.)

Repeat the same steps to secure the other end panel 
to the frame using the remaining fabric clips. 
 

NOTE:

 The end panels may be shipped as untrimmed 

rectangular pieces. If so, use scissors to trim the 
excess end panel material from inside the frame after 
attaching the panels to the end rafters. 

Continue by installing the remaining end wall framing.

8.

9.

10.

Ground Level

Tek Screw 
and Washer

Ground Level

Base Rail

Содержание SunBurst Dome Premium Gothic Style 106602






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды