manualshive.com logo in svg

ClearSpan 500 Series, Инструкция по эксплуатации, Страница: 44 / 61

Поделиться
Скачать
ClearSpan 500 Series Скачать руководство пользователя страница 44

44

Revision date: 07.11.14

INSTALL THE DROP-DOWN PANEL (continued)

10. Verify that the panel conduit remains against the 

baseboard and pull the slack from the cord.

11.  Thread the cord through the pulley (if this has not 

been done), weave the cord around the Tek screws as 

shown, and tighten the screws to secure the cord to 

the axle.

12. Move to the next pulley position and repeat the steps 

to measure, cut, and attach another cord to the panel 

and axle conduit. 

 

ATTENTION:

 If the cord length was correct for the 

first, cut additional cords to the same length. To 

ensure that the panel remains level during operation, 

verify that additional cords are wrapped around the 

axle conduit in the same direction and manner as the 

first cord.

13. Repeat the above steps until all cords are attached to 

the first panel along one side of the shelter. 

Diagram shows cords attached to the panel conduit 

and to the axle. Dashed line shows the position of the 

panel conduit. 

14. Continue by attaching the lower panel edge to the 

baseboard for the first panel installation.

Attach Lower Edge of the Panel to Baseboard

After tying all cords to the panel conduit and axle for the 

first panel assembly, secure the free edge (bottom) of the 

panel to the baseboard. 

View shown from outside the shelter.

Finished Grade

Drop-Down 

Side Panel

Optional 

End Wall 

Cladding

Retaining Board

Baseboard

9.  Move to the axle and drive two (2) FA4482 Tek screws 

with neo-bonded washers (102921B) into the axle 

conduit where the cord is located. 

Do not fully seat 

the Tek screws to the conduit.

 Allow space to remain 

between the washer and conduit.

Use customer-supplied dimension lumber as a retaining 

board for the lower edge of the panel. The retaining board 

must be at least 1" x 2" to adequately secure the panel to 

the baseboard. Use a 1" x 4" board for best results.

Complete the steps that follow on the next page to attach 

the lower edge of the panel.

Drop-Down Side Panel Installation

To the pulley attached 

to the ribbon board.

Cord

Axle

Measure from panel conduit up to 

pulley and down to drive axle.

Cord Length:

Panel Pocket with Conduit

Содержание 500 Series






























































Отзывы:

Нет отзывов