manualshive.com logo in svg

ClearSpan 500 Series, Инструкция по эксплуатации, Страница: 24 / 61

Поделиться
Скачать
ClearSpan 500 Series Скачать руководство пользователя страница 24

24

Revision date: 07.11.14

Attach 102197 U-Channel to Ribbon Board

102197 

U-Channel for 

cover install.

Buildings with a film cover require the installation of the 102197 u-channel. Use the photos below 

to install the u-channel.

Secure u-channel to ribbon board using FAH005B (1/4" x 2") carriage bolts, FAMF01B (1/4") 

fender washers, and FALB01B (1/4") nuts. Install channel flush with the ends of the ribbon board 

and end rafters. Pre-drill bolt holes using 5/16" bit. 

Space fasteners at 24" on-center throughout 

the length of the building on both sides.

 

Rafter Leg 

or Ground 

Post

2" x 6" 

Ribbon Board

(Part 1)

1" x 4" 

Ribbon Board

(Part 2)

U-Channel

FAH005B 

1/4" x 2"

Carriage Bolt

FAMF01B 

Fender Washer  

FALB01B 1/4" 

Nut

FA4652

Wood 

Screw

Customer-

Supplied 

Fasteners

Clamp or hold u-channel against the 

ribbon board. Drill a 5/16" bolt hole.

Attach u-channel to ribbon board 

using the 1/4" fasteners noted below.

Splice

Содержание 500 Series






























































Отзывы:

Нет отзывов