manualshive.com logo in svg

ClearSpan 500 Series, Инструкция по эксплуатации, Страница: 37 / 61

Поделиться
Скачать
ClearSpan 500 Series Скачать руководство пользователя страница 37

37

Revision date: 07.11.14

Film (or 5.2 oz) Cover Installation with Ridge Vent

9.  Take the remaining material and use it to cover the other side of the frame. Repeat steps to pull cover onto frame.

10. Secure cover to 111613Z144 rail attached to frame. Open vent to gain access to the double channel as needed. 

Using the proper lifts, work from inside the frame to secure cover to the u-channel attached to the frame. (See 

dashed line below.) Work down each end rafter to side run of double channel. Stretch cover and secure to 102197 

u-channel. Trim excess material from installed cover. Trim a few inches below the u-channel. 

Step 9

Step 10

Step 10

Step 10

Step 9

Photo above shows 102198 spring 

wire used to secure cover material 

to the u-channel attached to the 

end rafter. 

Always fully install wire in channel. 

Wear eye protection when installing 

spring!

11.  Continue with the next procedure.

Содержание 500 Series






























































Отзывы:

Нет отзывов