manualshive.com logo in svg

ClearSpan 500 Series, Инструкция по эксплуатации, Страница: 4 / 61

Поделиться
Скачать
ClearSpan 500 Series Скачать руководство пользователя страница 4

4

Revision date: 07.11.14

Baseboards, Retaining Boards, and Ribbon Boards

BASEBOARD AND RETAINING BOARDS

A customer-supplied baseboard and retaining board 

are required

 to attach the drop-down side panels. 

Recommended baseboard dimensions are 2" x 6". 

Recommended retaining board dimensions are 1" x 4". 

Use treated lumber for best results.

The baseboard runs the length of the frame at ground 

level. The retaining board secures the drop-down panel 

to the baseboard. 

The baseboard and retaining board are 

supplied by the customer. These are not included. 

 

Retaining boards are attached during the drop-down 

panel installation shown later in this guide.

Ground Level

Drop-Down 

Panel

Optional 

End Panel

Retaining Board

Baseboard

View shown from outside the shelter.

Fasteners to secure baseboards to the rafters are not 

included. For best results, use exterior grade fasteners.

Use the FA4652 wood grip screws to secure the retaining 

board to the baseboard. Space screws at 24" on-center. 

 

Contact your sales representative to purchase fasteners, 

or purchase locally when lumber is purchased.

Ground 

Level

Inside of 

Shelter

Outside of 

Shelter

Secure baseboard and ribbon 

board joints between rafters 

as shown for best results.

2-PIECE RIBBON BOARD REQUIRED

A customer-supplied two-piece ribbon board is required 

for the installation of the drop-down panels. Consult the 

Drop-Down Side Panel Installation procedure for details 

Customer supplies the materials for the ribbon board 

and fasteners to secure ribbon board to the frame.

Recommended ribbon board dimensions are shown 

below. Use treated lumber for best results.

End View

DIAGRAMS ARE NOT TO SCALE.

The ribbon boards run the length of 

the frame at the top of the drop-down 

panels. 

Recommended ribbon board 

dimensions for Part 1 are 2" x 6". 

Recommended ribbon board 

dimensions are for Part 2 are 1" x 4". 

Use treated lumber for best results.  

 

 Attach retaining boards during the 

drop-down panel installation. 

Finished Grade

Customer-Supplied Baseboard 

and Fasteners

Rafter Leg 

or Ground 

Post

2" x 6" 

Ribbon Board

(Part 1)

1" x 4" 

Ribbon Board

(Part 2)

U-Channel

FAH005B 

1/4" x 2"

Carriage Bolt

FAMF01B 

Fender Washer  

FALB01B 1/4" 

Nut

FA4652

Wood 

Screw

Customer-

Supplied 

Fasteners

Содержание 500 Series






























































Отзывы:

Нет отзывов