ClearSpan 500 Series Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 61

ClearSpan 500 Series Скачать руководство пользователя страница 12

12

Revision date: 07.11.14

Rafter Assembly–Optional Support Kit

Complete these basic steps:
1.  Slide the 103856 band clamps into position on the assembled rafter.
2.  Assemble the 1.90" diameter cross beam.
3.  Slide QH1404 band clamps onto the cross beam.
4.  Secure each splice of the cross beam using two (2) Tek screws.
5.  Verify dimensions and position of support kit components and install web components.
6.  Return to each band clamp and secure each clamp to the rafter using a Tek screw. Install Tek screw in a position

that will not contact the cover when it is installed.

CROSS BEAM

(190S099)

(190S099)

CROSS BEAM

CROSS BEAM

(190S099)

BAND CLAMP

(103856)

WEB

)

BAND CLAMP

ST06450D13G17S1

(103856)

(

)

(

(QH1404)

BAND CLAMP

ST09275D13G17S1

(QH1404)

BAND CLAMP

WEB

(103856)

BAND CLAMP

(QH1404)

BAND CLAMP

(QH1404)

(103856)

BAND CLAMP

WEB

(

ST09275D13G17S1

)

CROSS BEAM

(190P099)

BAND CLAMP

(103856)

BAND CLAMP

(103856)

BAND CLAMP

WEB

(

ST06450D13G17S1

)

RAFTER ASSEMBLY—Optional Support Kits

If the optional support kits were purchased, continue with the assembly steps that follow. Consult the diagrams

supplied with the rafter support kits for additional details. See also the diagram in the Quick Start section of this guide.

If the support kits were not purchased, continue with the frame assembly.

ATTENTION:

Support kit components are typically not installed for the end rafters when end wall framing is present.

«
...
10
11
12
13
14
...
»

Содержание 500 Series






























































Отзывы:

Нет отзывов