manualshive.com logo in svg

ClearSpan 500 Series, Инструкция по эксплуатации, Страница: 41 / 61

Поделиться
Скачать
ClearSpan 500 Series Скачать руководство пользователя страница 41

41

Revision date: 07.11.14

Axle Conduit

NOTE:

 If an optional end panel is installed at the 

other end of the frame, 

do not allow the free end of 

the axle to touch the inside surface of the panel. Trim 

pipe if needed. Axle must turn freely.  

 

If the assembled axle is too short, adjust each pipe 

at each pipe joint until the desired length is achieved, 

or add another section of pipe. At least 1-1/2" of the 

swaged end of a pipe must remain inside the plain 

end of the adjacent pipe.

14. After installing all sections of axle conduit for the 

first drop-down panel assembly, verify that the axle 

conduit is level and secure each conduit splice with a 

Tek screw (FA4482B) as shown above.

15. Move to the gearbox and test the assembly using the 

crank handle. 

 

NOTE:

 The assembled axle conduit should turn freely 

throughout the length of the shelter. Adjust the band 

clamps as needed. Reposition clamps and screws if 

these prevent smooth operation of the axle conduit. 

16. After verifying that the axle turns smoothly, repeat the 

procedure to assemble and attach the gearbox and 

axle conduit 

to the other side of the shelter.

10. Move inside the frame and slide a 106734 band clamp 

over the tapered end of the 131S075 pipe. 

NOTE:

 Verify that the axle pipe is level and secure the 

band clamp to the rafter leg (or ground post) using an 

FA4482B Tek screw.  

 

Do not install a band clamp at the end rafter where 

the gearbox mounting plate is attached. A band 

clamp is not needed in this position.

11.  Take a section of 131S075 pipe, attach it to the 

installed axle. 

Do not secure the joint at this time.

12. Slide another band clamp onto the tapered/swaged 

end of the conduit, level the conduit, and secure the 

band clamp to the next rafter leg/ground post. 

Actual 

rafter leg may differ slightly from the diagram.

13. Continue adding 131S075 conduit and band clamps 

and work toward the other end of the shelter. Verify that 

the axle conduit remains level throughout the length.  

Interior Rafter

Axle Conduit

106734 

Band 

Clamp

As seen from 

the inside.

A

As seen from the inside the shelter.

Axle Conduit

Ribbon Board

Band Clamp

A

17. Continue by attaching the drop-down panels.

Drop-Down Side Panel Installation

INSTALL THE DROP-DOWN PANEL (continued)

106734  

Band Clamp

Secure 

clamp to 

this rafter.

Содержание 500 Series






























































Отзывы:

Нет отзывов