manualshive.com logo in svg

ClearSpan 500 Series, Инструкция по эксплуатации, Страница: 40 / 61

Поделиться
Скачать
ClearSpan 500 Series Скачать руководство пользователя страница 40

40

Revision date: 07.11.14

8.  Take two (2) pieces of 131S075 (75") pipe, slide the 

swaged end of one into the plain end of the other and 

secure the joint using an FA4482B Tek screw.

9.  Using the diagram below, assemble the remaining 

components as shown and attach to gearbox. 

NOTE:

 Attach the plain end of the 131S075 pipe to 

the 102717 drive hub. Use the pipe insert to mark the 

hole location and drill the hole in the 131S075 pipe.  

 

Actual components may differ slightly from those 

shown in the diagrams. Have an assistant support the 

loose end of the axle to prevent damage. 

1/4" x 2" bolt (FAH005B)

and 1/4" nuts (FALB01B)

131S075 

Pipe (plain 

end)

102717 Drive

(3 pieces)

Mounting bolts 

included with the 

mounting plate. 

5/16" x 5" carriage bolts 

and 5/16" nuts to mount 

plate to end rafter

Diagram shows the assembled components. 

1/2"

If an optional end panel has been installed, carefully 

insert the axle through the axle conduit hole in the 

optional end wall cladding and attach to gearbox. 

NOTE:

 Diagrams shows gearbox mounted to the end 

rafter on the outside of the optional end wall cover.  

 

These instructions describe assembling the drop-

down axle in sections and working toward the other 

end of the frame. If desired and assistants are 

present, you can first fully assemble the axle and then 

attach the axle to the rafters as a single unit. 

This 

procedure is not shown.

Axle 

Conduit

Gearbox bolted 

to end rafter.

Drop-Down Side Panel Installation

INSTALL THE DROP-DOWN PANEL (continued)

Optional 

End Wall 

Cladding

Gearbox

Содержание 500 Series






























































Отзывы:

Нет отзывов