CleanSpace CS302, Инструкция пользователя

Страница: 34 / 90

34
 Avoid mechanical shocks or impacts from any sharp or hard objects.

Do not use or place the respirator in extreme heat, such as in direct sunlight, near heat sources, etc. The
battery will be damaged if its temperature rises above 212°F (100°C). Note: The respirator will stop
functioning if its internal temperature rises above 140°F (+60°C) or falls below 14°F (-10°C).
 Do not dispose of the respirator in a fire.
 Do not use the respirator in heavy rain, or allow it to get wet or immersed in liquid.
 Do not disassemble the blower case, there are no user serviceable parts inside.

Do not use the respirator if there are any signs of severe mechanical damage.
WARNING
IN THE EXTREMELY RARE CIRCUMSTANCE THAT THE BATTERY IS
DAMAGED AND ELECTROLYTE COMES IN CONTACT WITH EYES,
FLUSH WITH WATER IMMEDIATELY AND SEEK URGENT MEDICAL ATTENTION.
20. Cleaning
We recommended that you clean your respirator after every use. The mask, blower, neck support and harness need
to be cleaned separately. Disassemble the mask, neck support and harness from the blower before cleaning.
CleanSpace Cleaning Wipes are recommended as a simple and effective method of cleaning the blower and masks.
CLEANING THE HALF MASK
There are two methods for cleaning the mask. Before washing the mask, remove the Standard Valve Cover or BIO
Exhalation Valve Cover covering the exhalation valve leaf – See Section 23 for more detail.
The Valve Cover, BIO Exhalation Valve Cover and the Steri-Plus Exhalation Filter Case can all be cleaned using the
methods described for the mask; or disposed of and replaced with a new one, depending on the disinfection policies
of the user. New BIO Exhalation Valve Covers may be ordered from your CleanSpace distributor and are part
number CS3026. The Standard Exhalation Valve Cover part number is PAF-1111 and the Steri-Plus Exhalation
Filter Case part number is CS3038.
1. CleanSpace Non-Alcohol Wipes for face piece
 CleanSpace Cleaning Wipes are impregnated with benzalkonium chloride, a bactericidal solution ideally
suited for silicone face pieces.

 To clean the exhalation valve, remove the Valve Cover (using the instructions above), gently wipe the
leaf edge. Replace the Valve Cover before use.

2. Hand wash in warm soapy water
 Wash the mask thoroughly with a mild detergent in warm water (less than 122°F (50°C)).

A soft brush or sponge can be used to remove any stubborn dirt or grit.
 To clean the exhalation valve, gently wash the warm water solution through the valve and use a sponge
to gently clean the valve surface.


Rinse the mask and valve well in warm running water. IMPORTANT: If the mask is not rinsed thoroughly,
residue from cleaning solution may irritate the wearer’s skin or cause the valve to stick. Replace the
Valve Cover before use.
Drying the mask
After cleaning, allow the mask to air dry in a clean environment, valve up to prevent water pooling. Note: Do not dry
the mask by exposing directly to heat i.e. hair dryers or heaters. The mask can also be hand-dried with a clean, lint-
free cloth. IMPORTANT: Cleaning can cause the exhalation valve leaf to stick. Before use, check that the exhalation
valve leaf operates freely by gently lifting the valve. Replace the Valve Cover before use.
WARNING
The Steri-Plus and HALO BIO Exhalation Filters (CS3039 and CS3027 respectively) are electrostatic
filters and their performance will be degraded by exposure to certain organic solvents including
isopropanol (IPA), xylene and toluene. Always remove the Exhalation Filter before cleaning the mask. If
there is a possibility that the Exhalation Filter has become contaminated with any solvent, replace it.
WARNING
NEVER DRY THE MASK OR EXHALATION VALVE WITH A CLOTH THAT MAY LEAVE BEHIND LINT.
Lint contamination of the exhalation valve may cause it to leak, resulting in overexposure to
contaminants and lead to sickness.