Claydon HYBRID MOUNTED Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 51

background image

17

D

PRE-WORK PREPARATION

OPERATORS MANUAL - HYBRID MOUNTED

Transporting the Drill

Raise the machine off the ground and fold the wings fully upright (applies to 4m, 4.8m and 6m machines).

Once folded, turn the hydraulic tap parallel to the cylinder to lock the wings in the upright position (Figure

6). To unfold the wings turn the hydraulic tap in the opposite direction and operate the spool valve.

WARNING

NEVER TRANSPORT ALONG PUBLIC HIGHWAY WITHOUT

ISOLATING THE FOLDING WINGS & MARKER ARMS

Location of wing isolation hydraulic tap

Location of marker arm isolation hydraulic tap

When the drill is in transport, the Hydraulic valve taps (located on the hydraulic cylinders, Figure 9) should
be locked off to prevent the marker arms being unfolded.

«
...
15
16
17
18
19
...
»

Содержание HYBRID MOUNTED




















































Отзывы:

Нет отзывов

Похожие инструкции для HYBRID MOUNTED

Бренд: GE Страницы: 14

Бренд: GE Страницы: 11

Бренд: GE Страницы: 20

Druck ADTS 2 Series

Бренд: GE Страницы: 18

Бренд: Oemtools Страницы: 4

Бренд: Panlux Страницы: 2

PORTABLE ICE FISHING KIT

Бренд: Garmin Страницы: 5

Бренд: Laserworld Страницы: 8

Бренд: Laserworld Страницы: 6

Бренд: LaserLiner Страницы: 56

Бренд: LaserLiner Страницы: 54

Бренд: Tar River Страницы: 26

Бренд: ZOLL Страницы: 38

Бренд: ZOLL Страницы: 36

Nature2 Fusion soft

Бренд: Zodiac Pool Systems Страницы: 52

Бренд: Oliver Страницы: 38

Бренд: G21 Страницы: 7

Бренд: LSI Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды