Claydon HYBRID MOUNTED Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 51

background image

27

E

IN FIELD OPERATION

OPERATORS MANUAL - HYBRID MOUNTED

SETTING THE FAN SPEED

The ISOCAN system displays the fan speed on the drill.

The ISOCAN system has been pre-set with a ‘Low fan limit’ and a ‘High fan limit’ which will alarm if the
fan runs either above or below the recommended speed. Being above or below will have an impact on

the drilling performance, ensure the speed remains within this margin. The fan speed is adjusted from the

tractor by increasing or decreasing the hydraulic flow output to the fan motor from the tractor there is

no physical adjustment on the drill. It is possible that the fan speed will need to be adjusted according to

the seed rates, density and size of seeds being drilled. There are no recommended settings it is purely user
defined to achieve the best results for your requirements. An ideal guide would be to set the fan between

3500 RPM and 4000 RPM for most crops.

«
...
25
26
27
28
29
...
»

Содержание HYBRID MOUNTED




















































Отзывы:

Нет отзывов

Похожие инструкции для HYBRID MOUNTED

Бренд: Sagola Страницы: 8

Sportsound SSR-200

Бренд: Daktronics Страницы: 5

Бренд: NCR Страницы: 20

Бренд: DARAY Страницы: 32

Body Armor Night Splint

Бренд: Darco Страницы: 2

Бренд: MacDon Страницы: 74

Бренд: Quivogne Страницы: 13

Бренд: Task Force Tips Страницы: 20

Бренд: MAHA Страницы: 21

Бренд: MAGUIRE Страницы: 47

Бренд: ACS Страницы: 28

Бренд: LABORIE Страницы: 116

Бренд: Fisher Scientific Страницы: 44

Haymakers Hooimakers F80-350V

Бренд: Falcon Страницы: 38

Бренд: Lightronics Страницы: 6

Бренд: Neopost Страницы: 10

Бренд: KAM Страницы: 8

Бренд: Jandy Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды