Clarke TIGER 3000A Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 28

background image

19

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

CLEANING THE FUEL STRAINER

Just inside the fuel tank is a fuel strainer. Inspect this periodically and remove
any contaminants which may have accumulated.

1. Remove the fuel tank cap.

2. Remove the fuel strainer.

3. Remove any contaminants.

4. Replace the fuel strainer.

•

Do not operate pressure
washer without fuel strainer
properly installed.

CLEANING THE AIR FILTER

1. Release the two clips on the air filter cover.

2. Remove the air filter cover.

3. Remove the air filter elements.

4. Wash the elements in a solution of warm water and mild detergent.

5. Rinse thoroughly and leave the elements to dry. Once it is completely dry,

immerse the filter in clean engine oil and sqeeze to remove excess oil.

•

If the air filter is damaged contact CLARKE spare parts department
for a replacement.

6. Replace the filter into its original position and refit the air filter cover.

WARNING: DO NOT USE FLAMMABLE SOLVENTS OR PETROL TO CLEAN THE
AIR FILTER

«
...
17
18
19
20
21
...
»

Содержание TIGER 3000A





























Отзывы:

Нет отзывов

Похожие инструкции для TIGER 3000A

Бренд: Echo Страницы: 20

Бренд: Kärcher Страницы: 17

K 5 Full Control

Бренд: Kärcher Страницы: 16

Бренд: Kärcher Страницы: 12

K 3.800 eco!ogic

Бренд: Kärcher Страницы: 244

Бренд: Kärcher Страницы: 64

Бренд: Kärcher Страницы: 16

Бренд: Kärcher Страницы: 212

Бренд: Kärcher Страницы: 48

Бренд: Kärcher Страницы: 344

HDS-E 3.3/25-4M Ec

Бренд: Kärcher Страницы: 52

Бренд: Kärcher Страницы: 417

Бренд: Kärcher Страницы: 13

Бренд: Kärcher Страницы: 474

Бренд: Kärcher Страницы: 428

HDS 1.7/12 U Ed

Бренд: Kärcher Страницы: 48

Бренд: Kärcher Страницы: 352

Бренд: Kärcher Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды