background image

3

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

GENERAL SAFETY RULES 

1.

DO NOT

 point the spray at other people, animals, electrical equipment or the 

machine itself.

2.

DO NOT 

hold your finger over the high pressure nozzle.

3.

DO NOT

 let children or untrained personnel use this machine.

4.

DO NOT 

operate the machine with any of the covers removed.

5.

DO NOT 

try to repair this machine. Always refer to your CLARKE service 

department for all repairs.

6.

DO NOT 

supply any liquid other than water to the water inlet.

7.

DO NOT 

use the detergent pickup facility to introduce flammable liquids/

solvents, e.g. paint thinners, petrol, oil as there is a risk of explosion.

8.

ALWAYS

 release the remaining pressure in the system turn off the water supply 

and operate the trigger before you remove hoses or accessories. 

9.

ALWAYS

 keep the machine dry and away from the water spray.

10.

ALWAYS

 use protective clothing and safety glasses. Loose particles and other 

items can be propelled at high speed by the water spray.

11.

ALWAYS

 hold the gun securely and expect it to ‘kick’ when you pull the 

trigger.

12.

ALWAYS

 respect the requirements of the local water company. Pressure 

washers may only be connected to the mains water supply if a system 
separator (also known as a backflow preventer) is installed in the supply hose.

13.

ALWAYS

 disconnect from the water supply, and make sure that you drain the 

system when not in use. Keep in a cool dry location.

14.

ONLY

 use detergents that are suitable for pressure washers, we recommend 

that you use CLARKE Traffic Film Remover or CLARKE Wash and WAX 
(available from your dealer). 

15.

WARNING

 High pressure hoses, fittings and couplings are important for the 

safety of the machine. Use only hoses, fittings and couplings recommended 
by the manufacturer.

16.

WARNING

 Water that passes through a system separator (also known as a 

backflow preventer) is not safe to drink.

17.

DO NOT

 use the pressure washer if there is damage to the inlet/outlet hose or 

the machine

.

WARNING: Water at high pressure can be dangerous and can cause 
damage if the operator is careless. Never allow anyone to operate this 
pressure washer unless they are familiar with the safety precautions.

Содержание TIGER 3000A





























Отзывы: