Clarke TIGER 3000A Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 28

background image

12

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

5. Set the engine switch to the on (I)

position.

6. Pull the recoil starting handle

lightly until you start to feel
resistance and then pull up
sharply to start the engine.

•

You may have to do this more
than once.

7. Once the engine has warmed up,

slide the choke lever to the OPEN
position.

•

The pressure washer is now
ready for use.

8. Release the trigger lock.

9. Ensuring that you have a firm

footing and that you are also
holding the gun assembly and
spray lance firmly, pull the trigger
on the gun to start water flow.

•

The lance and gun will kick
back when the trigger is first
pulled.

WARNING: ONCE THE PRESSURE WASHER ENGINE HAS STARTED, RELEASE
THE STARTING HANDLE SLOWLY TO AVOID INJURY/DAMAGE AS IT
RECOILS.

«
...
10
11
12
13
14
...
»

Содержание TIGER 3000A





























Отзывы:

Нет отзывов

Похожие инструкции для TIGER 3000A

Бренд: Haier Страницы: 14

Бренд: Haier Страницы: 2

Бренд: Kärcher Страницы: 17

K 5 Full Control

Бренд: Kärcher Страницы: 16

Бренд: Kärcher Страницы: 12

K 3.800 eco!ogic

Бренд: Kärcher Страницы: 244

Бренд: Kärcher Страницы: 64

Бренд: Kärcher Страницы: 16

Бренд: Kärcher Страницы: 212

Бренд: Kärcher Страницы: 48

Бренд: Kärcher Страницы: 344

HDS-E 3.3/25-4M Ec

Бренд: Kärcher Страницы: 52

Бренд: Kärcher Страницы: 417

Бренд: Kärcher Страницы: 13

Бренд: Kärcher Страницы: 474

Бренд: Kärcher Страницы: 428

HDS 1.7/12 U Ed

Бренд: Kärcher Страницы: 48

Бренд: Kärcher Страницы: 352

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды