Clarke TIGER 3000A Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 28

background image

6

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

ASSEMBLY

Unpack your pressure washer and check to ensure the following items are
present.

Contact your CLARKE dealer immediately if any parts are missing or
damaged.

CONNECTING THE WHEELS

1. Slide the axles into the locating

tube as shown.

•

Make sure the ball catch locks
into the small hole on the
bottom of the locating tube.

2. Add the 2 axle covers as shown.

1 x Power Washer

2 x Wheel & Axle Assembly

1 x Hose Bracket c/w Fixings

1 x Nozzle Cleaning Pin

1 x Gun / Lance Bracket c/w Fixings

1 x Tap Adaptor

1 x Hose

1 x Detergent Hose c/w Filter

1 x Lance Assembly

1 x Upper Handle c/w Fixings

1 x Gun Assembly

1 x Engine Manual

1 x Spark Plug Box Spanner

1 x 3m Inlet water hose

1 x Tommy Bar

1 x Water Filter (may be supplied
already fitted)

«
...
4
5
6
7
8
...
»

Содержание TIGER 3000A





























Отзывы:

Нет отзывов

Похожие инструкции для TIGER 3000A

Бренд: Vax Страницы: 8

WA422PRHD Series

Бренд: Samsung Страницы: 36

Бренд: Generac Power Systems Страницы: 24

Appliances Profile PFWS4605

Бренд: GE Страницы: 88

Бренд: Philco Страницы: 32

FLOORWASH 1000 Battery

Бренд: NAMCO Страницы: 24

SUNJOE SPX4001-RM

Бренд: SNOWJOE Страницы: 18

Бренд: Indesit Страницы: 16

Бренд: Russell Hobbs Страницы: 28

Бренд: Samsung Страницы: 65

Бренд: Samsung Страницы: 68

Бренд: Candy Страницы: 17

Бренд: Candy Страницы: 41

Бренд: Candy Страницы: 120

RO 496DWMC7/1-S

Бренд: Candy Страницы: 132

Lavatrice CS44 128TXME/2-S

Бренд: Candy Страницы: 136

RP586BWMBCB/1-S

Бренд: Candy Страницы: 145

Бренд: Bosch Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды