Clarke TIGER 3000A Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 28

background image

8

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

FITTING THE LANCE/HOSE HOLDER

Fit the holders into the positions
shown and secure using the washers
and nuts provided.

CONNECTING THE HIGH PRESSURE HOSE

CONNECT THE HOSE TO THE GUN

1. Screw the high pressure hose onto

the gun assembly.

•

Tighten the connector, hand
tight only. Do not use a
spanner.

NOTE:

Make sure the connection is
secure.

CONNECT THE HOSE TO THE PRESSURE WASHER

1. Screw the hose on to the pressure

washer.

•

Tighten the connector, hand
tight only, Do not use a
spanner.

NOTE:

Make sure the connection is
secure.

ASSEMBLING THE LANCE

Connect the spray lance to the gun
assembly and tighten securely by
turning the locking ring.

«
...
6
7
8
9
10
...
»

Содержание TIGER 3000A





























Отзывы:

Нет отзывов

Похожие инструкции для TIGER 3000A

Бренд: GE Страницы: 108

Бренд: Kärcher Страницы: 134

Бренд: Candy Страницы: 136

Бренд: Candy Страницы: 41

Бренд: Instant Pot Страницы: 4

Бренд: Generac Power Systems Страницы: 24

XPERT-HD 3.8/35 P

Бренд: Landa Страницы: 16

Бренд: Spitwater Страницы: 21

Бренд: Hamach Страницы: 55

Бренд: Daewoo Страницы: 50

Super 20 CL8761

Бренд: Speed Queen Страницы: 41

Бренд: Daewoo Страницы: 58

Бренд: Kodiak Страницы: 14

Бренд: Kärcher Страницы: 112

Бренд: Briggs & Stratton Страницы: 3

Бренд: AEG Страницы: 48

Бренд: AEG Страницы: 56

Бренд: AEG Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды