background image

C H A P T E R

2-1

PA-2FEISL 100BASE-T Fast Ethernet/ISL Port Adapter Installation and Configuration

OL-3475-02

2

Preparing for Installation

This chapter describes the general equipment, safety, and site preparation requirements for installing the 
PA-2FEISL port adapter. This chapter contains the following sections:

Required Tools and Equipment, page 2-1

 

Software and Hardware Requirements, page 2-1

 

Safety Guidelines, page 2-3

 

FCC Class A Compliance, page 2-10

 

Required Tools and Equipment

You need the following tools and parts to install a port adapter. If you need additional equipment, contact 
a service representative for ordering information.

PA-2FEISL-TX(=) or PA-2FEISL-FX(=) port adapter.

VIP2 (for installation in the Cisco 7000 series or Cisco 7500 series chassis only). (For information 
about the specific VIP model that supports the PA-2FEISL, see the 

“Software and Hardware 

Requirements” section on page 2-1

.)

Cables appropriate for the port adapter’s interfaces (RJ-45 and multimode optical-fiber cables are 
not available from Cisco; they are available from commercial cable vendors).

Number 1 Phillips and a 3/16-inch, flat-blade screwdriver (for VIP2 installation only).

Number 2 Phillips screwdriver.

Your own ESD-prevention equipment or the disposable grounding wrist strap included with all 
upgrade kits, field-replaceable units (FRUs), and spares.

Antistatic mat.

Antistatic container.

Software and Hardware Requirements

Table 2-1

 lists the recommended minimum Cisco IOS software release required to use the PA-2FEISL 

in supported router platforms.

Содержание PA-2FEISL-FX



























































Отзывы: