Cisco PA-2FEISL-FX Скачать руководство пользователя | Manualshive

Страница: 23 / 58

background image

C H A P T E R

2-1

PA-2FEISL 100BASE-T Fast Ethernet/ISL Port Adapter Installation and Configuration

OL-3475-02

2

Preparing for Installation

This chapter describes the general equipment, safety, and site preparation requirements for installing the
PA-2FEISL port adapter. This chapter contains the following sections:

•

Required Tools and Equipment, page 2-1

•

Software and Hardware Requirements, page 2-1

•

Safety Guidelines, page 2-3

•

FCC Class A Compliance, page 2-10

Required Tools and Equipment

You need the following tools and parts to install a port adapter. If you need additional equipment, contact
a service representative for ordering information.

•

PA-2FEISL-TX(=) or PA-2FEISL-FX(=) port adapter.

•

VIP2 (for installation in the Cisco 7000 series or Cisco 7500 series chassis only). (For information
about the specific VIP model that supports the PA-2FEISL, see the

“Software and Hardware

Requirements” section on page 2-1

.)

•

Cables appropriate for the port adapter’s interfaces (RJ-45 and multimode optical-fiber cables are
not available from Cisco; they are available from commercial cable vendors).

•

Number 1 Phillips and a 3/16-inch, flat-blade screwdriver (for VIP2 installation only).

•

Number 2 Phillips screwdriver.

•

Your own ESD-prevention equipment or the disposable grounding wrist strap included with all
upgrade kits, field-replaceable units (FRUs), and spares.

•

Antistatic mat.

•

Antistatic container.

Software and Hardware Requirements

lists the recommended minimum Cisco IOS software release required to use the PA-2FEISL

in supported router platforms.

«
...
21
22
23
24
25
...
»

Содержание PA-2FEISL-FX



























































Отзывы:

Нет отзывов

Похожие инструкции для PA-2FEISL-FX

Бренд: Paradyne Страницы: 3

Бренд: Paradyne Страницы: 15

USB External Sound Card Adapter

Бренд: StarTech.com Страницы: 9

Бренд: Radio Shack Страницы: 36

Бренд: cable matters Страницы: 8

Бренд: CC&C Страницы: 24

Бренд: LevelOne Страницы: 29

LevelOne WUA-0616

Бренд: CP TECHNOLOGIES Страницы: 5

Бренд: Conceptronic Страницы: 11

Бренд: NETGEAR Страницы: 2

Бренд: Intermec Страницы: 4

Бренд: KTI Networks Страницы: 23

Бренд: Linksys Страницы: 26

Бренд: ZyXEL Communications Страницы: 3

XE602 - Powerline Ethernet Adapter

Бренд: NETGEAR Страницы: 2

Бренд: i-tecc Страницы: 28

Бренд: i-tec Страницы: 48

USB 2.0 to VGA Pro

Бренд: SIIG Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды