manualshive.com logo in svg

Cisco PA-2FEISL-FX, Руководство по установке и настройке

Поделиться
Скачать
Cisco PA-2FEISL-FX Скачать руководство пользователя страница 21

1-11

PA-2FEISL 100BASE-T Fast Ethernet/ISL Port Adapter Installation and Configuration

OL-3475-02

Chapter 1      Overview

  Identifying Interface Addresses

Figure 1-13

 shows port adapters installed in slot 1 and slot 2 of a Cisco uBR7246 router. The 

port adapter slots are numbered slot 1 and slot 2 for the Cisco uBR7246, and slot 1 for the 
Cisco uBR7223 and the Cisco uBR7246 VXR. (Slot 0 is always reserved for the Fast Ethernet port on 
the I/O controller—if present.) The individual interfaces always begin with 0. The number of additional 
interfaces depends on the number of interface ports on a port adapter.

The interface addresses of the interfaces on a PA-2FEISL in port adapter slot 2 are 2/0 and 2/1 
(port adapter slot 2 and interfaces 0 and 1). If the

 

PA-2FEISL was in port adapter slot 1, these same 

interfaces would be numbered 1/0 and 1/1 (port adapter slot 1 and interfaces 0 and 1).

VIP2 Interface Addresses

This section describes how to identify the interface addresses used for the PA-2FEISL on a VIP2 in 
Cisco 7000 series and Cisco 7500 series routers.

Note

Although the processor slots in the 7-slot Cisco 7000 and Cisco 7507 and 13-slot Cisco 7513 and 
Cisco 7576 are vertically oriented and those in the 5-slot Cisco 7010 and Cisco 7505 are horizontally 
oriented, all Cisco 7000 series and Cisco 7500 series routers use the same method for slot and port 
numbering. 

See 

Table 1-4

 for the interface address format. The interface address is composed of a three-part number 

in the format 

interface-processor-slot

 

number/port-adapter-slot-number/interface-port- number

.

Figure 1-15

 shows a sample Cisco 7505 system. The interface addresses of the

 

PA-2FEISL are 3/1/0 

through 3/1/1). If the port adapter was in port adapter slot 0 on the VIP2, these same interface addresses 
would be numbered 3/0/0 through 3/0/1.

If you remove the

 

VIP2 with the 

PA-2FEISL 

(shown in 

Figure 1-15

) from interface processor slot 3 and 

install it in interface processor slot 2, the interface addresses become 2/1/0 through 2/1/1. 

Figure 1-15 Fast Ethernet/ISL Interface Port Number Example—Cisco 7505

Note

If you remove the PA-2FEISL-equipped VIP2 (shown in 

Figure 1-15

) from interface processor slot 3 and 

install it in interface processor slot 2, the interface addresses become 2/1/0 through 2/1/1.

12063

Slot 0

Slot 1

Slot 2

Slot 3

Interface 
processor
slots

EJ

EC

T

SL

O

T 

0

SL

O

T 

1

N

O

R

M

AL

C

PU

 H

AL

T

R

ES

ET

C

O

N

SO

LE

ROUTE SWITCH PROCESSOR

AU

X.

3/0/0 and 3/0/1 (PA-2FEISL-TX port adapter)

ENABLED

LINK

FAST ETHERNET/ISL 

0

1

LINK

Содержание PA-2FEISL-FX



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды