background image

The type of shelf that the AIP resides in determines the version of AIP that should replace the failed
AIP. The 15454-SA-ANSI shelf (P/N: 800-19857) and 15454-SA-HD (P/N: 800-24848) currently
use the 5A AIP, (P/N: 73-7665-01). The 15454-SA-NEBS3E, 15454-SA-NEBS3, and 15454-SA-R1
(P/N: 800-07149) shelves and earlier use the 2A AIP (P/N: 73-5262-01).

Caution

Do not put a 2A AIP (P/N: 73-5262-01) into a 15454-SA-ANSI (P/N: 800-19857) or 15454-SA-HD
(P/N: 800-24848) shelf; doing so will cause a blown fuse on the AIP.

Caution

Step 11

Attach the fan-tray assembly power cable to the new AIP.

Step 12

Place the new AIP on the backplane by plugging the panel into the backplane using the DIN connector.

Step 13

Replace the AIP cover over the AIP and secure the cover with the two screws.

Step 14

Replace the lower backplane cover and secure the cover with the five screws.

Step 15

In node view (single-shelf mode) or multishelf view (multishelf mode), click the

Provisioning > Network

tabs.

Cisco recommends that TCC2/TCC2P/TCC3/TNC/TSC card resets be performed in a maintenance
window to avoid any potential service disruptions.

Caution

Step 16

Reset the standby TCC2/TCC2P/TCC3/TNC/TSC card:

a) Right-click the standby TCC2/TCC2P/TCC3/TNC/TSC card and choose

Reset Card

.

b) Click

Yes

in the Resetting Card dialog box. As the card resets, a loading (Ldg) indication appears on the

card in CTC.

The reset takes approximately five minutes. Do not perform any other steps until the reset is
complete.

Note

Step 17

Complete the “DLP-G250 Reset the TCC2/TCC2P/TCC3/TNC/TSC Card” task in the

Cisco ONS 15454

DWDM Configuration Guide

to reset the active TCC2/TCC2P/TCC3/TNC/TSC card.

Step 18

From the

File

drop-down list, choose

Exit

to exit the CTC session.

Step 19

Log back into the node. In the Login dialog box, choose

(None)

from the Additional Nodes drop-down list.

Step 20

Record the new MAC address:

a) In node view (single-shelf mode) or multishelf view (multishelf mode), click the

Provisioning > Network

tabs.

b) Record the MAC address shown in the General tab.

Step 21

In node view (single-shelf mode) or multishelf view (multishelf mode), click the

Circuits

tab. Note that all

circuits listed have a status of PARTIAL.

Step 22

In node view (single-shelf mode) or multishelf view (multishelf mode), choose

Repair Circuits

from the

Tools

drop-down list. The Circuit Repair dialog box appears.

Step 23

Read the instructions in the Circuit Repair dialog box. If all the steps in the dialog box have been completed,
click

Next

. Ensure that you have the old and new MAC addresses.

Step 24

The Node MAC Addresses dialog box appears:

a) From the Node drop-down list, choose the name of the node where you replaced the AIP.
b) In the Old MAC Address field, enter the old MAC address that was recorded in Step 3.
c) Click

Next

.

Step 25

The Repair Circuits dialog box appears. Read the information in the dialog box and click

Finish

.

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

28

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G117 Replace the ANSI Shelf Alarm Interface Panel

Содержание ONS 15454 M6

































Отзывы: