Cisco ONS 15454 M6 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 32

background image

None

—

No

2A

2A

NEBS3E or NEBS3

MEA on 10G

—

Yes

2A

2A

NEBS3E or NEBS3

None

—

No

5A

2A

NEBS3E or NEBS3

MEA on 10G

—

Yes

5A

2A

NEBS3E or NEBS3

None

—

No

2A

2A

ANSI or HD

MEA on fan tray, AIP, and
Ethernet

2.5G compatible

Yes

2A

2A

ANSI or HD

MEA on fan tray and AIP

10G compatible

Yes

2A

2A

ANSI or HD

None

Either

No

5A

2A

ANSI or HD

MEA on fan tray and Ethernet

2.5G compatible

Yes

5A

2A

ANSI or HD

MEA on fan tray

10G compatible

Yes

5A

2A

ANSI or HD

MEA on AIP

Either

No

2A

5A

ANSI or HD

MEA on AIP and Ethernet

2.5G compatible

Yes

2A

5A

ANSI or HD

MEA on AIP

10G compatible

Yes

2A

5A

ANSI or HD

None

Either

No

5A

5A

ANSI or HD

None

Either

Yes

5A

5A

ANSI or HD

1

15454-SA-NEBS3E (P/N: 800-07149-xx) or 15454-SA-NEBS3 (P/N: 800-06741-xx) = shelf
assemblies released before ONS 15454 Release 3.115454-SA-ANSI (P/N: 800-19857-01) =
ONS 15454 Release 3.1 and later shelf assembly15454-SA-HD (P/N: 800-24848) = ONS 15454
Release 3.1 and later shelf assembly

2

5A Fan Tray = 15454-FTA3 (P/N: 800-19858-xx), 15454-FTA3-T (P/N: 800-21448-xx),
15454-CC-FTA (P/N: 800-27558-xx)2A Fan Tray = 15454-FTA2 (P/Ns: 800-07145-xx,
800-07385-xx, 800-19591-xx, 800-19590-xx)

3

5A AIP (P/N: 73-7665-01), 2A AIP (P/N: 73-5262-01)

4

10G cards include the XC10G, OC192, and OC48AS.

5

2.5G compatible indicates cards that are compatible with the XCVT cross-connect card. 10G
compatible indicates cards that are compatible with the XC10G and XC-VXC-10G cross-connect
cards.

Table 2: Incompatibility Alarms for ONS 15454 ETSI

Alarms

Ethernet Cards

10G Cards

Fan Tray

Shelf Assembly

None

—

No

2A

15454E-SA-ETSI

MEA on 10G

—

Yes

2A

15454E-SA-ETSI

None

—

No

2A

15454E-SA-ETSI

MEA on 10G

—

Yes

2A

15454E-SA-ETSI

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

18

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G116 Replace the Fan-Tray Assembly of the ONS 15454 Shelf Assembly

«
...
16
17
18
19
20
...
»

Содержание ONS 15454 M6

































Отзывы:

Нет отзывов

Похожие инструкции для ONS 15454 M6

IPS Wireless SELD-102

Бренд: Flowserve Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды