Cisco ONS 15454 M6 Скачать руководство пользователя страница 13

Страница: 13 / 32

Step 2

Read the manufacturer (cleaning cartridge) instructions to insert the connector into the cleaning cartridge.

Step 3

Slide the lever on the cartridge to swipe the connector surface.

Step 4

Insert the fiber connector into the applicable adapter or attach a dust cap to the fiber connector.

If you must replace a dust cap on a connector, first verify that the dust cap is clean.

Note

Step 5

Return to your originating procedure (NTP).

DLP-G262 Clean Fiber Connectors with CLETOP

This task cleans the fiber connectors with CLETOP.

Purpose

Type A Fiber Optic Connector Cleaner (CLETOP reel)

Optical receiver cleaning stick

Tools/Equipment

None

Prerequisite Procedures

Required

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

Procedure

Step 1

Remove the dust cap from the fiber connector.

Step 2

Press the lever up to open the shutter door. Each time you press the lever, you expose a clean wiping surface.

Step 3

Insert the connector into the CLETOP cleaning cassette slot, rotate one quarter turn, and gently swipe
downwards.

Step 4

Use an inspection microscope to inspect each fiber connector for dirt, cracks, or scratches. If the connector
is not clean, repeat Steps 1 to 3.

Step 5

Insert the fiber connector into the applicable adapter or attach a dust cap to the fiber connector.

If you must replace a dust cap on a connector, first verify that the dust cap is clean. To clean the
dust cap, wipe the outside of the cap using a dry, lint-free wipe and the inside of the dust cap using
a CLETOP stick swab (14100400).

Note

Step 6

Return to your originating procedure (NTP).

DLP-G263 Clean the Fiber Adapters

This task cleans the fiber adapters.

Purpose

CLETOP stick swab

Tools/Equipment

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

DLP-G262 Clean Fiber Connectors with CLETOP

Содержание ONS 15454 M6

































Результаты поиска

Содержание ONS 15454 M6

Отзывы:

Похожие инструкции для ONS 15454 M6

Бренды по названию

Популярные бренды

Cisco ONS 15454 M6, Руководство по обслуживанию

Результаты поиска

Содержание ONS 15454 M6

Отзывы:

Похожие инструкции для ONS 15454 M6

Бренды по названию

Популярные бренды