manualshive.com logo in svg

Cisco ONS 15454 M6, Руководство по обслуживанию

Устройство Cisco ONS 15454 M6 - это надежное оборудование для сетей передачи данных, обеспечивающее высокую производительность. Для поддержания работы устройства в отличном состоянии, необходимо регулярно проводить техническое обслуживание. Вы можете скачать бесплатное Руководство по обслуживанию на manualshive.com.

Поделиться
Скачать
background image

Figure 13: Removing or Replacing the Fan-Tray Assembly (Front Door Removed) (ETSI)

Step 8

If you are replacing the fan-tray air filter and it is installed beneath the fan-tray assembly, slide the existing
air filter out of the shelf assembly and replace it before replacing the fan-tray assembly.

If you are replacing the fan-tray air filter and it is installed in the external bottom bracket (ANSI shelf only),
you can slide the existing air filter out of the bracket and replace it at anytime. For more information on the
fan-tray air filter, see the

NTP-G114 Inspect and Replace the Air Filter, on page 1

.

Step 9

Slide the new fan tray into the shelf assembly until the electrical plug at the rear of the tray plugs into the
corresponding receptacle on the backplane.

Step 10

To verify that the tray has plugged into the backplane, ensure that the LCD on the front of the fan tray is
activated.

If you removed the door, complete the

NTP-G40 Replace the Front Door , on page 14

.

The estimated time of replacement by a skilled technician is 2 minutes.

Note

Stop. You have completed this procedure.

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

21

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G116 Replace the Fan-Tray Assembly of the ONS 15454 Shelf Assembly

Содержание ONS 15454 M6

































Отзывы:

Нет отзывов

Похожие инструкции для ONS 15454 M6

Бренды по названию

Популярные бренды

Загрузить еще бренды