manualshive.com logo in svg

Cisco ONS 15454 M6, Руководство по обслуживанию

Устройство Cisco ONS 15454 M6 - это надежное оборудование для сетей передачи данных, обеспечивающее высокую производительность. Для поддержания работы устройства в отличном состоянии, необходимо регулярно проводить техническое обслуживание. Вы можете скачать бесплатное Руководство по обслуживанию на manualshive.com.

Поделиться
Скачать
background image

Figure 2: ETSI Shelf Fan-Tray Air Filter in an External Filter Bracket (Front Door Removed)

Step 4

Push the outer side of the handles on the fan-tray assembly to expose the handles.

Step 5

Pull the handles and slide the fan-tray assembly one half inch (12.7 mm) out of the shelf assembly and wait
until the fans stop.

Step 6

When the fans have stopped, pull the fan-tray assembly completely out of the shelf assembly.

Step 7

Gently remove the air filter from the shelf assembly. Be careful not to dislodge any dust that might have
collected on the filter.

Step 8

Visually inspect the air filter material for dirt and dust.

Step 9

Replace the air filter with a new one if the air filter is dirty or clogged with dust.

Do not leave the fan tray out of the chassis for an extended period of time because excessive heat
can damage the ONS 15454 cards.

Caution

Step 10

Replace the air filter:

a) If the air filter is installed in the external filter brackets, slide the new air filter all the way to the back of

the brackets.

b) If the filter is installed below the fan-tray assembly, slide the new air filter into the recessed compartment

at the bottom of the shelf assembly. Put the front edge of the air filter flush against the front edge of the
recessed compartment. Push the fan tray back into the shelf assembly.

If the fan tray does not slide all the way to the back of the shelf assembly, pull the fan tray out
and readjust the position of the air filter until the fan tray fits correctly.

Caution

On a powered-up ONS 15454, the fans start immediately after the fan-tray assembly is correctly
inserted.

Note

Step 11

To verify that the tray is plugged into the backplane, ensure that the LCD on the front of the fan-tray assembly
is activated and displays node information.

Step 12

Rotate the retractable handles back into their compartments.

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

4

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G114 Inspect and Replace the Air Filter

Содержание ONS 15454 M6

































Отзывы:

Нет отзывов

Похожие инструкции для ONS 15454 M6

Бренды по названию

Популярные бренды

Загрузить еще бренды