Cisco ONS 15454 M6 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 32

background image

New air filter, pinned hex key tool

Tools/Equipment

None

Prerequisite Procedures

As needed

Required/As Needed

Onsite

Onsite/Remote

None

Security Level

Do not reach into a vacant slot or chassis while you install or remove a module or a fan. Exposed circuitry
could constitute an energy hazard.

Statement 206

Warning

The air filters are single-use only. They must not be cleaned and reused. This is a Telcordia NEBS requirement,
GR-63-CORE Issue 4.

Note

Air filters must be inspected every month. If they are dirty or clogged with dust, they must be replaced with
a new air filter.

Note

If you install the air filter below 15454E-CC-FTA or 15454-CC-FTA, only filters with part numbers
700-23193-01 and 700-23194-01 can be used in this configuration.

Note

Although the air filter can work with older fan trays if it is installed with either side facing up, it is recommended
that you install it with the metal bracing facing up to preserve the surface of the filter. You must install the
air filter with the metal bracing facing up with 15454E-CC-FTA or 15454-CC-FTA.

Caution

To install the air filter inside the air ramp unit (15454E-AIR-RAMP or 15454-AIR-RAMP), use the ETSI
version of the air filter (15454-FTF2 or 15454E-FTF4).

Note

Procedure

Step 1

If the air filter is installed in the external filter brackets, slide the filter out of the brackets while being careful
not to dislodge any dust that might have collected on the filter and proceed to Step 8.

Figure 1: ANSI Shelf

Fan-Tray Air Filter in an External Filter Bracket (Front Door Removed), on page 3

shows the fan-tray air

filter in an external filter bracket on an ANSI shelf.

Figure 2: ETSI Shelf Fan-Tray Air Filter in an External

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

2

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G114 Inspect and Replace the Air Filter

«
1
2
3
4
...
»

Содержание ONS 15454 M6

































Отзывы:

Нет отзывов

Похожие инструкции для ONS 15454 M6

SureCross DX99 FlexPower Series

Бренд: Banner Страницы: 8

Бренд: Calix Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды