Cisco ONS 15454 M6 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 32

background image

None

Security Level

The 15454-FTA3 fan-tray assembly can only be installed in ONS 15454 R3.1 and later shelf assemblies
(15454-SA-ANSI, P/N: 800-19857; 15454-SA-HD, P/N: 800-24848). The fan-tray assembly includes a pin
that prevents it from being installed in ONS 15454 shelf assemblies released before ONS 15454 R3.1
(15454-SA-NEBS3E, 15454-SA-NEBS3, and 15454-SA-R1, P/N: 800-07149). Equipment damage can result
from attempting to install the 15454-FTA3 in a incompatible shelf assembly.

Caution

Do not force a fan-tray assembly into place. Doing so can damage the connectors on the fan tray and/or the
connectors on the backplane.

Caution

15454-CC-FTA (ANSI) is compatible with Software R2.2.2 and greater, and shelf assemblies 15454-SA-ANSI
and 15454-SA-HD. 15454E-CC-FTA (ETSI) is compatible with Software R4.0 and greater, and shelf assembly
15454-SA-ETSI.

Caution

As with the FTA3, the 15454E-CC-FTA and 15454-CC-FTA Fan Fail LED on the front of the fan-tray
assembly illuminates when one or more fans fail to indicate that a fan-tray assembly or AIP replacement is
required. But the Fan Fail LED on the 15454E-CC-FTA and 15454-CC-FTA will also illuminate when only
one power source is connected to the chassis, and or any fuse blows. In such conditions, the Fan Alarm is
triggered and the fans run at maximum speed.

Caution

To replace the fan-tray assembly, it is not necessary to move any of the cable management facilities.

Note

Procedure

Step 1

Review

Table 1: Incompatibility Alarms for ONS 15454 ANSI , on page 17

(ANSI) or

Table 2: Incompatibility

Alarms for ONS 15454 ETSI , on page 18

(ETSI) to ensure that you have compatible components when

replacing the fan-tray assembly. Note the alarms that will be generated when an incompatibility occurs.

If you need to determine the hardware that has been installed on a node, click the Inventory tab in
node view.

Note

Table 1: Incompatibility Alarms for ONS 15454 ANSI

Alarms

Ethernet Cards

10G Cards

AIP

Fan Tray

Shelf Assembly

Mismatch of equipment attributes
(MEA) on the alarm interface
panel (AIP)

—

—

No fuse

—

—

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

17

Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf

NTP-G116 Replace the Fan-Tray Assembly of the ONS 15454 Shelf Assembly

«
...
15
16
17
18
19
...
»

Содержание ONS 15454 M6

































Отзывы:

Нет отзывов

Похожие инструкции для ONS 15454 M6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды