Cisco Octal-Port DMT ATU-C Line Card Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 32

background image

Octal-Port DMT ATU-C Line Card

Supported Platforms

4

Cisco IOS Release 12.1(6)DA

Supported Platforms

DSLAMs

This feature supports the 8xDMT line card on the Cisco 6015, Cisco 6160, and Cisco 6260 platforms
with NI-2.

Table 1

details the total available ADSL modem connections for each chassis.

The 8xDMT is designed for use with the Cisco 6015, Cisco 6160, or Cisco 6260 chassis in one of the
following configurations:

•

Cisco 6015, Cisco 6160, or Cisco 6260 with a POTS splitter chassis—Provisions one modem
directly and is physically connected to one specific subscriber line through the POTS
splitter chassis.

•

Cisco 6015, Cisco 6160, or Cisco 6260 without a POTS splitter chassis—Provisions one modem
directly and is physically connected to one specific subscriber line through the main distribution
frame (MDF) connections.

CPE

•

Cisco 677

•

Cisco 678

•

Cisco Soho 77

•

Cisco 827

•

Cisco IAD 2423

•

Cisco 1700, Cisco 2600, and Cisco 3600 series with ADSL WIC

•

Alcatel Speed Touch Home

•

Alcatel Speed Touch Pro

•

Efficient Networks 5260 and 5262

•

Westell modems based on Alcatel Microelectronics firmware version 1.4.1

•

CPE using ADI chipsets with firmware versions 0X3019BE70 (Version 3.0),
0X2219BE04 (Version 2.2), or 0X2019BE2D (Version 2.0) should operate similar to the Cisco 677

Note

A correct firmware version does not guarantee interoperation with third-party CPE. Some
hardware variations can affect performance and error rates. Test the interoperation of CPE
with the 8xDMT in the targeted deployment model before provisioning service.

Table 1

Number of Available Modem Connections for Each Chassis

Chassis

Number of Available 8xDMT
Slots

Total ADSL Modem Connections

Cisco 6015

6

48

Cisco 6160

32

256

Cisco 6260

30

240

«
...
2
3
4
5
6
...
»

Содержание Octal-Port DMT ATU-C Line Card

































Отзывы:

Нет отзывов

Похожие инструкции для Octal-Port DMT ATU-C Line Card

Бренд: Linksys Страницы: 2

Бренд: IEI Technology Страницы: 19

Бренд: IEI Technology Страницы: 87

Бренд: IEI Technology Страницы: 3

Бренд: RadiSys Страницы: 44

Бренд: Lanner Страницы: 2

Бренд: CSS Страницы: 2

Бренд: Alesis Страницы: 46

RUGGEDSWITCH RS900G

Бренд: RuggedCom Страницы: 23

Бренд: ICP DAS USA Страницы: 8

Бренд: Xenya Страницы: 189

Бренд: B+B SmartWorx Страницы: 52

ZyXEL ZyAIR B-120

Бренд: ZyXEL Communications Страницы: 20

Easy Tool-ID BSG TID-05-T30-00-005

Бренд: Balluff Страницы: 46

memonizerWORKSTATION

Бренд: MEMON Страницы: 2

Бренд: Kohler Страницы: 32

Бренд: Lutron Electronics Страницы: 4

Бренд: BWI Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды