Cisco Octal-Port DMT ATU-C Line Card Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 32

background image

Octal-Port DMT ATU-C Line Card

dmt margin

17

Cisco IOS Release 12.1(6)DA

dmt margin

To set upstream and downstream signal-to-noise ratio (SNR) margins for a DMT profile, use the dmt
margin command. To reset this command to the default value, use the no form of this command.

dmt margin downstream dmt-margin upstream dmt-margin

Syntax Description

Defaults

Downstream: 6 dB

Upstream: 6 dB

Command Modes

Profile configuration.

Command History

Usage Guidelines

Caution

This command causes the port to retrain when you change the parameter.

Setting a parameter to its current value does not cause a retrain. If a port is training when you change
this value, the port untrains and retrains to the new value.

Examples

In this example, the command sets the SNR margins of the default profile to 12 dB downstream and
6 dB upstream:

DSLAM# configure terminal

DSLAM(config)# dsl-profile default

DSLAM(config-dsl-prof)# dmt margin downstream 12 upstream 6

Related Commands

None.

dmt-margin

Enter the upstream and downstream SNR margins in decibels. The range is
0 to 15.

Release

Modification

12.0(5)DA

This command was introduced.

«
...
15
16
17
18
19
...
»

Содержание Octal-Port DMT ATU-C Line Card

































Отзывы:

Нет отзывов

Похожие инструкции для Octal-Port DMT ATU-C Line Card

Wireless Router

Бренд: Watchguard Страницы: 11

Бренд: D-Link Страницы: 32

Бренд: D-Link Страницы: 28

Бренд: D-Link Страницы: 48

Бренд: D-Link Страницы: 83

Бренд: D-Link Страницы: 155

BB-HGW700A - Network Camera Router

Бренд: Panasonic Страницы: 10

Бренд: Jetter Страницы: 35

Бренд: Danfoss Страницы: 61

Бренд: X-Micro Страницы: 74

Бренд: IEI Technology Страницы: 3

Бренд: Abocom Страницы: 2

Net2Air Ins-40085-US

Бренд: Paxton Страницы: 4

Бренд: ZyXEL Communications Страницы: 215

Low Power Series

Бренд: FabiaTech Страницы: 77

Бренд: Cowfish Technologies Страницы: 38

LonWorks Communication Module LN-01

Бренд: Delta Electronics Страницы: 1

Бренд: Aurora Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды