Cisco D9824 Скачать руководство пользователя страница 286 | Manualshive

Страница: 286 / 416

background image

Chapter 5 Web GUI Setup and Monitoring

264

Firmware Version

Description

Boot5514/Boot7109

Software boot-loader version that initializes and

configures the STi5514/STi7109 device on the HDR2
(main) board. This is the master controller for the
D9824 receiver.

CPLD-5514/CPLD-7109

Software Configurable Programmable Logic Device
version attached to the STi5514/STi7109.

FP-PIC

Front panel controller version for the D9824
receiver.

FPGA Type

The manufacturer's designation for the FPGA
device on the HDR2 (main) board.

FPGA ID

This value is used by the decoder software to
determine the features available in the FPGA.

Safe SW Version

Version of the installed safe application, which

cannot be overwritten by another downloaded
application.

Safe FPGA Version

Version of the installed safe FPGA image, which

cannot be overwritten by another downloaded
FPGA image.

App Safe Limit

Indicates the version of the oldest application that

can be installed  on the current  unit. If  this  value is
zero, the oldest  application  limit is the Safe  SW
Version.  If  this is greater than  zero, the shown  value
or older  and the Safe  SW  Version  is the limit. Older
applications  will not  be installed.

The

HW Board Versions

table displays the revisions, option bits, and serial numbers

of the HRD2 (main) board.

In the

APP/FPGA Downloads

area, click

Browse

to select the new version of FPGA

or the D9824 Advanced Multi Decryption Receiver software application. The Open

dialog opens. Choose the upgrade file and click

Open

. Click

Download

to download

the selected upgrade file. File formats that can be downloaded include application

CDTs and FPGA CDTs. The

State

field in the

Download Status

area displays the

progress of the download. When the download is complete, a Successfully
Completed message is displayed at the top of the Versions page.

Note:

For application downloads, once the download is complete, the D9824 receiver

will reboot automatically. For FPGA downloads, you must click

Reboot Receiver

in

the Service Actions page (

Support

>

Service Actions

) to manually reboot the D9824

receiver and complete the download. This is to facilitate the typical case in which the
user intends to flash the FPGA file (no auto reboot) followed by an APP download
(auto reboot).

«
...
284
285
286
287
288
...
»

Содержание D9824

































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для D9824

Бренд: Hammarlund Страницы: 38

Бренд: Hammarlund Страницы: 22

Бренд: Hammarlund Страницы: 87

Бренд: Icom Страницы: 4

Бренд: Javad Страницы: 10

Бренд: Javad Страницы: 7

Бренд: Javad Страницы: 4

Бренд: EKT Страницы: 8

Бренд: Clas Ohlson Страницы: 30

Бренд: RADICAL Страницы: 13

Бренд: Alpine Страницы: 78

Бренд: RF-Link Страницы: 4

Бренд: Marantz Страницы: 91

Бренд: Pyle Страницы: 4

Бренд: Wetekom Страницы: 22

Personal PA Receiver PPA R19

Бренд: Williams Sound Страницы: 2

Бренд: CityCom Страницы: 16

Бренд: Sencor Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды