Cisco Catalyst 6880-X Скачать руководство пользователя страница 83

Страница: 83 / 124

Step 2

Always remove any cables before removing the port card from the slot. Disconnect the cables from the SFP+
transceiver modules.

Step 3

(Optional) Remove the SFP+ transceiver modules from the port card.

Step 4

Press on the extraction handle to release the latch and rotate the handle outwards to extract the card.

Figure 35: Releasing the Latch

Step 5

Grasp the port card, and carefully slide it out of the slot. You can use the other hand too.

Figure 36: Removing the Port Card

Step 6

Install a replacement port card or a blank module in the slot.

Step 7

Place the port card that you removed in an antistatic bag or other protective environment.

You can close the latch so it locks, and use the handle to carry the port card module.

Note

Catalyst 6880-X Switch Hardware Installation Guide

OL-30827-02

Installing the Modular Port Card

Removing a Modular Port Card

Содержание Catalyst 6880-X





























































































































Результаты поиска

Содержание Catalyst 6880-X

Отзывы:

Похожие инструкции для Catalyst 6880-X

Бренды по названию

Популярные бренды

Cisco Catalyst 6880-X, Руководство по установке оборудования

Результаты поиска

Содержание Catalyst 6880-X

Отзывы:

Похожие инструкции для Catalyst 6880-X

Бренды по названию

Популярные бренды