Cisco Catalyst 6880-X Скачать руководство пользователя страница 26

Страница: 26 / 124

DC-Input Power Supply LEDs

The 3000 W DC-input power supply includes LEDs on the front of the module. The different states of the
LEDs are described in the following table.

Figure 8: DC-Input Power Supply LED Locations

On/Off switch

Location of LEDs on DC-input power supply

Table 10: DC-Input Power Supply LED Indicators

Description

Color/State

LED

Primary DC input current is at acceptable
level.

Solid green

IN1

Primary DC input current is outside valid
range.

Blinking green

IN1

Secondary DC input current is at acceptable
level.

Solid green

IN2

Secondary DC input current is outside valid
range.

Blinking green

IN2

Output DC current is at acceptable level.

Solid green

OUT

Output DC current is outside valid range.

Blinking green

OUT

Power supply unit is functioning normally.

Off

FAULT

The unit has failed self-diagnostic test or is
not operational.

Blinking red

FAULT

Catalyst 6880-X Switch Hardware Installation Guide

OL-30827-02

Product Overview

LED Indicators

Содержание Catalyst 6880-X





























































































































Результаты поиска

Содержание Catalyst 6880-X

Отзывы:

Похожие инструкции для Catalyst 6880-X

Бренды по названию

Популярные бренды

Cisco Catalyst 6880-X, Руководство по установке оборудования

Результаты поиска

Содержание Catalyst 6880-X

Отзывы:

Похожие инструкции для Catalyst 6880-X

Бренды по названию

Популярные бренды