Cisco Catalyst 6880-X Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 124

background image

b) Verify that the OUTPUT LED has turned off. If the LED is still on, return to Step 1.
c) If you are removing a DC-input power supply, ensure that the power is turned off at the power source by

turning off the power for that circuit, and then verify that the INPUT LEDs turn off.

Step 2

Detach the power and ground cables, as follows:

•

For the AC-input power supply, unplug the power cables that are attached to the power supply and the
power source.

•

For the DC-input power supply, open the terminal box, and use a Phillips screwdriver to remove the
power cables from their terminals. Replace the terminal box cover. Remove the power cables from the
power source.

Step 3

Remove the power supply from the chassis, as follows:

a) Press the ejector latch on the left of the power supply.
b) Pull the power supply partially out of the slot by its handle.
c) Place your other hand under the unit to support its weight.
d) Pull the power supply fully from the slot.

If you intend to operate the switch without installing another power supply in the empty slot, then
you must reinstall the blank cover over the empty power supply slot to ensure proper air flow in
the system and for safety reasons.

Caution

Catalyst 6880-X Switch Hardware Installation Guide

60

OL-30827-02

Installing and Removing Power Supplies

Removing Power Supplies

«
...
70
71
72
73
74
...
»

Содержание Catalyst 6880-X





























































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 6880-X

Бренд: La Toulousaine Страницы: 6

Бренд: i3 International Страницы: 2

Бренд: FAAC Страницы: 2

Бренд: Yeastar Technology Страницы: 11

Бренд: ABB Страницы: 10

Бренд: Lindy Страницы: 70

Бренд: Baxall Страницы: 33

Бренд: Contemporary Controls Страницы: 4

2X2 VGA SWITCHER

Бренд: Gefen Страницы: 12

Signature ANTENNA GENIUS 8x2 v2 PLUS

Бренд: 4O3A Страницы: 57

Бренд: Videplus Страницы: 13

Бренд: Gira Страницы: 2

Бренд: I-Tech Страницы: 19

Бренд: Linkskey Страницы: 2

Бренд: MicroNet Страницы: 123

TNS5000D Series

Бренд: 3onedata Страницы: 3

Бренд: LINK-MI Страницы: 9

Бренд: Blue Sea Systems Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды