Cisco Catalyst 6880-X Скачать руководство пользователя страница 116 | Manualshive

Страница: 116 / 124

background image

Solving Problems at the System Component Level

The key to success when troubleshooting the system is to isolate the problem to a specific system component.
The first step is to compare what the system

is doing

to what it

should be doing

. Because a startup problem

can usually be attributed to a single component, it is more efficient to isolate the problem to a subsystem rather
than troubleshoot each separate component in the system.

The switch consists of these subsystems:

•

Power supplies

•

Fan tray assembly

The chassis fan tray assembly should operate whenever system power is on. You should see the FAN
LED turn green and hear the fan tray assembly operating. A red FAN LED indicates that one or more
fans in the fan tray assembly is not operating. You should immediately contact a Customer Service
representative if the fan tray assembly is not functioning properly. There are no installation adjustments
that you can make if the fan tray assembly does not function properly at initial startup.

Identifying Startup Problems

LEDs indicate all system states in the startup sequence. By checking the LEDs, you can determine when and
where the system failed in the startup sequence.

Procedure

Step 1

Turn on the power supplies. You should immediately hear the system fan tray assembly begin to operate.

•

If you do not hear the fans operating, see the

Troubleshooting the Power Supply, on page 104

section.

•

If you determine that the power supplies are functioning normally and that the fan tray assembly is
faulty, contact a customer service representative.

•

If the fan tray assembly does not function properly at initial startup, there are no installation adjustments
that you can make. To replace the fan tray assembly, see

Troubleshooting the Fan Tray , on page 105

section.

Step 2

If the startup information and system banner do not display at startup, verify that the terminal is set correctly
and that it is connected properly to the console port.

Troubleshooting the Power Supply

If the INPUT OK LED does not light after you turn on the power switch, follow these steps to isolate a power
subsystem problem:

Catalyst 6880-X Switch Hardware Installation Guide

104

OL-30827-02

Troubleshooting

Solving Problems at the System Component Level

«
...
114
115
116
117
118
...
»

Содержание Catalyst 6880-X





























































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 6880-X

Бренд: AbleNet Страницы: 2

Бренд: IBM Страницы: 2

DynaGST/2402G GEP-33224T-1

Бренд: UNICOM Страницы: 1

Cleveland Controls RSS-498-013

Бренд: UNICONTROL Electronic Страницы: 2

OS20-001000T5T5TAFUHB

Бренд: Hirschmann Страницы: 40

FlowPoint 2100 12

Бренд: Cabletron Systems Страницы: 36

Бренд: Hawking Страницы: 2

Бренд: N-Tron Страницы: 17

AMX ENOVA DVX-3250HD-SP

Бренд: Harman Страницы: 119

Бренд: VADA Страницы: 4

IPES-3424DSFP-2P

Бренд: Lantech Страницы: 26

Бренд: The Siemon Company Страницы: 2

Бренд: TP-Link Страницы: 2

Бренд: AV Access Страницы: 16

Бренд: SMART-AVI Страницы: 8

Бренд: SMC Networks Страницы: 3

PDI WaveStar BCMS

Бренд: Eaton Страницы: 54

Бренд: ATEN Страницы: 303

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды