Cisco Catalyst 6880-X Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 124

background image

Description

Task

The various ports on the chassis must be connected
to the network. This process can involve only
attaching a network interface cable to the port or it
can include the installation of a transceiver of some
type in port and then attaching the network interface
cable to the transceiver.

Cabling the chassis and modules to the network

After completing the network cabling and making
sure that system ground is connected, the power
supplies can be turned on. The system powers up and
runs through a set of built-in diagnostics.

Powering up the chassis

Safety Warnings

Class 1 laser product. Statement 1008

Warning

This unit is intended for installation in restricted access areas. A restricted access area can be accessed
only through the use of a special tool, lock and key, or other means of security. Statement 1017

Warning

This unit might have more than one power supply connection. All connections must be removed to
de-energize the unit. Statement 1028

Warning

Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Statement 1030

Warning

To prevent personal injury or damage to the chassis, never attempt to lift or tilt the chassis using the
handles on modules (such as power supplies, fans, or cards); these types of handles are not designed to
support the weight of the unit. Statement 1032

Warning

Hazardous voltage or energy is present on the backplane when the system is operating. Use caution when
servicing. Statement 1034

Warning

This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation.
Install only in accordance with national and local wiring regulations. Statement 1045

Warning

Catalyst 6880-X Switch Hardware Installation Guide

34

OL-30827-02

Installing the Switch

Safety Warnings

«
...
44
45
46
47
48
...
»

Содержание Catalyst 6880-X





























































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 6880-X

Hub M50 Mesh Cube

Бренд: Xunison Страницы: 11

Бренд: DANLERS Страницы: 2

Бренд: CZHOON Страницы: 4

Бренд: StarTech.com Страницы: 24

Бренд: GE Страницы: 2

Бренд: Eaton Страницы: 2

Бренд: nedis Страницы: 24

IPES-3424DSFP-2P

Бренд: Lantech Страницы: 26

Бренд: Lindy Страницы: 6

Бренд: Lantech Страницы: 80

FS5300-EI Series

Бренд: H3C Страницы: 57

Extricom AT-EXLS-3000

Бренд: Allied Telesis Страницы: 120

Бренд: Woxcon Страницы: 51

IP Power 9258 DS

Бренд: Aviosys Страницы: 37

Бренд: Omron Страницы: 11

AT-HDDVI1616-AM

Бренд: Atlona Страницы: 15

Бренд: AETEK Страницы: 2

Essentials EXP-SW-0401-H2

Бренд: Wyrestorm Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды