Cisco ASR1002 - ASR 1002 Router Скачать руководство пользователя страница 91

Страница: 91 / 462

Software Upgrade Process

ISSU Upgrade for Redundant Platforms

Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide

Examples

The following example shows how to perfrom consolidated package upgrade in a dual route processor
configuration:

Router(config)#

ip tftp source-interface gigabitethernet 0

Router#

copy tftp bootflash:

Address or name of remote host []?

172.17.16.81

Source filename []?

/auto/tftp-users/user/asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin

Destination filename [asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin]?

Accessing

tftp://172.17.16.81//auto/tftp-users/user/asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.

bin...

Loading /auto/tftp-users/user/asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin from

172.17.16.81 (via GigabitEthernet0):

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!

[OK - 209227980 bytes]

209227980 bytes copied in 329.215 secs (635536 bytes/sec)

Router#

copy bootflash:asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin stby-bootflash:

Destination filename [asr1000rp1-adventerprisek9.02.01.01.122-33.XNA1.bin]?

Step 21

show version

active-RP

running

show version

active-RP

provisioned

show platform

show running-configuration

(Optional) Enter the

show version

show platform

show runnning-configuration

commands to

confirm that the upgrade completed successfully, as
follows:

•

show version

—Confirm that the correct

software version is running on your router and
that the RP was booted from the correct file.

•

show running-configuration

—Confirm that

the booting configuration, in particular the boot
system statements, are correct.

Tip

Use the

show running-config | include boot

command to display only the boot statements
from the

show running-configuration

output.

•

show platform

— Confirm that both RP0 and

RP1 are correctly running as active and standby.

Step 22

hw-module slot

RP-slot

reload

Example:

Router#

hw-module slot R0 reload

Reload the new software on the Standby RP.

Command or Action

Purpose

Содержание ASR1002 - ASR 1002 Router















































































































































































































































































































































































































































































Результаты поиска

Содержание ASR1002 - ASR 1002 Router

Отзывы:

Бренды по названию

Популярные бренды

Cisco ASR1002 - ASR 1002 Router, Руководство по настройке программного обеспечения

Результаты поиска

Содержание ASR1002 - ASR 1002 Router

Отзывы:

Бренды по названию

Популярные бренды