manualshive.com logo in svg

Cisco ASR1002 - ASR 1002 Router, Руководство по настройке программного обеспечения

Поделиться
Скачать
Cisco ASR1002 - ASR 1002 Router Скачать руководство пользователя страница 237

 

      Broadband Scalability and Performance

  IP Sessions Scaling

3

Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide

  –

Intelligent Services Gateway (ISG) Services are not supported 

  –

Point-to-Point Protocol over ATM (PPPoA) and Point-to-Point Protocol over Ethernet 
(PPPoEoA) sessions are not supported 

  –

RP2 requires 16 GB DRAM to support 48000 sessions

Note

If any of the listed restrictions is not met, the router scales to a maximum of 32000 sessions 
only.

  •

Restrictions on the 64000 session scaling with RP2 and ESP-40G: 

  –

ISG services are not supported 

  –

PPPoA and PPPoEoA sessions are not supported 

  –

Per-session QoS with queuing actions (for example, shaping) is not supported

  –

RP2 requires 16 GB DRAM to support 64000 sessions

Note

If any of the listed restrictions is not met, the router scales to a maximum of 32000 sessions 
or 48000 sessions only.

  •

Restrictions on 64000 L2TP tunnel scaling with RP2 and ESP-40G:

  –

ISG services are not supported

  –

Per-session QoS is not supported

  –

RP2 requires 16 GB DRAM

  –

High Availability (SSO) is not supported

Note

If any of the listed restrictions is not met, the router scales to a maximum of 16000 L2TP 
tunnels.

  •

The RP2 and ESP10 hardware combination is not supported for broadband.

  •

RP1 with 2GB of DRAM is not recommended for broadband deployment.

IP Sessions Scaling

The ASR 1000 Series Routers can be deployed as an IP session aggregator. The maximum number of IP 
sessions that can be supported depends on the hardware combination. 

Table 20

 lists the hardware 

combination and the maximum number of IP sessions that are supported.

The session limits apply to all variety of IP session initiators: DHCP, unclassified Mac address, 
unclassified IP, and RADIUS proxy. 

Table 20

Maximum Number of IP Sessions Supported on ASR 1000 Hardware  

Chassis

RP

ESP

IP Session

ISG Traffic Class

1001

Integrated

ESP-2.5G or ESP-5G

8000

24000

1002

Integrated RP1

ESP-5G

12000

36000

Содержание ASR1002 - ASR 1002 Router















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды