manualshive.com logo in svg

Cisco ASR1002 - ASR 1002 Router, Руководство по настройке программного обеспечения

Поделиться
Скачать
Cisco ASR1002 - ASR 1002 Router Скачать руководство пользователя страница 236

 

      Broadband Scalability and Performance

  PPP Sessions and L2TP Tunnel Scaling

2

Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide

PPP Sessions and L2TP Tunnel Scaling

The ASR 1000 Series Routers are deployed in a variety of broadband deployment models for terminating 
Point-to-Point Protocol (PPP) Sessions and initiating or terminating Layer 2 Tunneling Protocol (L2TP) 
tunnels. The maximum number of PPP sessions and L2TP tunnels is dependent on the hardware 
combination. 

Table 18

 lists the hardware combinations and the maximum number of PPP sessions and 

L2TP tunnels that are supported in Cisco IOS XE Release 3.3. For information about the restrictions for 
PPP sessions and L2TP tunnel scaling, see the 

“Restrictions for PPP Sessions and L2TP Tunnel Scaling” 

section on page 2

.

Table 19

 lists the virtual circuit limits for ASR 1000 ATM SPAs, effective from Cisco IOS XE 

Release 3.5.

Restrictions for PPP Sessions and L2TP Tunnel Scaling

This section lists the restrictions for the PPP sessions and L2TP tunnel scalability.

  •

To achieve maximum scaling for the 1001, 1002, and 1004 chassis, we recommend software 
redundancy be disabled for broadband applications, and only hardware redundancy be configured.

  •

Restrictions on 48000 session scaling with RP2 and ESP-40G include:

Table 18

Maximum Number of PPP Sessions and L2TP Tunnels Supported on ASR 1000 
Hardware 

Chassis

RP

ESP

PPP Session

L2TP Tunnel

1001

Integrated

ESP-2.5G or 
ESP-5G

8000

4000

1002

Integrated 
RP1

ESP-5G

12000

6000

1004, 1006

RP1

ESP-10G or 
ESP-20G

24000

12000

1004, 1006

RP2

ESP-20G

32000

16000

1004, 1006, 1013

RP2

ESP-40G

32000

1

, 48000, or 64000

1.

32000 session scaling with RP2 and ESP-40G is fully supported without any additional restrictions. For restrictions on 48000 
and 64000 see the 

“Restrictions for PPP Sessions and L2TP Tunnel Scaling” section on page 2

.

64000

Table 19

ASR 1000 ATM Virtual Circuit (VC) Limits 

ASR1000-SIP10

ASR1000-SIP40

SPA/SIP

Number of VCs

SPA/SIP

Number of VCs

SPA-1XOC12-ATM-V2

4000 VCs per Port, 
4000 VCs per SPA

SPA-1XOC12-ATM-V2

4000 VCs per Port, 
4000 VCs per SPA

SPA-1XOC3-ATM-V2

4000 VCs per Port, 
4000 VCs per SPA

SPA-1XOC3-ATM-V2

4000 VCs per Port, 
4000 VCs per SPA

SPA-3XOC3-ATM-V2

3000 VCs per Port, 
9000 VCs per SPA

SPA-3XOC3-ATM-V2

4000 VCs per Port, 
12000 VCs per SPA

ASR1000-SIP10

24000 VCs per SIP

ASR1000-SIP40

32000 VCs per SIP

Содержание ASR1002 - ASR 1002 Router















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды