manualshive.com logo in svg

Cisco ASR1002 - ASR 1002 Router, Руководство по настройке программного обеспечения

Поделиться
Скачать
Cisco ASR1002 - ASR 1002 Router Скачать руководство пользователя страница 406

 

      Configuring MPLS Layer 2 VPNs

  Additional References

30

Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide

Note

Ethernet-to-EtherChannel over MPLS (Bridge) Interworking mode is also supported under VLAN.

Additional References

The following sections provide references related to the Frame Relay to ATM Bridged Interworking and 
xconnect support on GEC (VPWS) features.

Related Documents

Standards

MIBs

Step 23

clock source internal

Specifies that the T1/E1 link uses the internal clock 
from the interface. 

Step 24

xconnect

 

peer-loopback vc-id pw-class pe-class-name

Binds an attachment circuit to a pseudowire to 
configure an AToM static pseudowire, specifies 
MPLS as the tunneling method, and enters the 
xconnect configuration mode.

Command or Action 

Purpose

Related Topic

Document Title

Cisco IOS commands

Cisco IOS Master Commands List, All Releases

Basics of MPLS

MPLS: Basic MPLS Configuration Guide, Cisco IOS XE Release 3S

MPLS Layer 2 VPNs

MPLS Layer 2 VPNs Configuration Guide, Cisco IOS XE Release 3S

Cisco IOS Configuration Fundamentals

Cisco IOS Configuration Fundamentals Command Reference

Standard

Title

No new or modified standards are supported by this 
feature.

—

MIB

MIBs Link

  •

CISCO-IETF-PW-MIB

  •

CISCO-IETF-PW-MPLS-MIB 

To locate and download MIBs for selected platforms, Cisco IOS 
releases, and feature sets, use the Cisco MIB Locator found at the 
following URL:

http://www.cisco.com/go/mibs

Содержание ASR1002 - ASR 1002 Router















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды