manualshive.com logo in svg

Cisco ASR1002 - ASR 1002 Router, Руководство по настройке программного обеспечения

Поделиться
Скачать
Cisco ASR1002 - ASR 1002 Router Скачать руководство пользователя страница 401

 

      Configuring MPLS Layer 2 VPNs

  Configuring Gigabit EtherChannel for Virtual Private Wire Service

25

Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide

DETAILED STEPS

Command or Action

Purpose

Step 1

enable

Changes the privilege level for the corresponding CLI 
session.

Step 2

configure terminal

Example:

Router# 

configure terminal

Enters the global configuration mode.

Step 3

mpls label protocol ldp

Example:

Router#

 mpls label protocol ldp

Specifies that LDP is the default label distribution 
protocol. 

Step 4

interface loopback 

loopback-interface-number

Example:

Router# 

interface loopback 1

Specifies the loopback interface, and enters the interface 
configuration mode.

Step 5

ip address 

ip-address mask

Example:

Router#

 ip address 10.10.2.1 255.255.255.0

Sets the IP address and mask for the loopback interface.

Step 6

exit

Exits the interface configuration mode.

Step 7

pseudowire-class

 

pw-class-name

Example:

Router(config)#

 pseudowire-class gec-bridged

Specifies the name of a Layer 2 pseudowire class and 
enters the pseudowire class configuration mode.

Step 8

encapsulation mpls

Example:

Router(config-pw)# 

encapsulation mpls

Uses MPLS as the tunneling method to encapsulate data 
in the pseudowire.

Step 9

interworking ethernet

Example:

Router(config-pw)# 

interworking ethernet

Enables the L2VPN Interworking feature, and causes 
Ethernet frames to be extracted from the attachment 
circuit and sent over the pseudowire. Ethernet end-to-end 
transmission is assumed. Attachment circuit frames that 
do not contain Ethernet frames are dropped. In the case 
of VLAN, the VLAN tag is removed, which leaves a pure 
Ethernet frame. 

Step 10

interface GigabitEthernet 

slot | subslot | port

Example:

Router(config)# 

interface GigabitEthernet 0/0/1

Specifies the Gigabit Ethernet interface, and enters the 
interface configuration mode.

Step 11

xconnect

 

peer-ip-address vc-id

 

encapsulation mpls 

pseudowire-class 

pw-class-name

Example:

Router(config-if)#

 xconnect 

10.0.0.1 

707 

encapsulation mpl pseudowire-class gec-bridged

Binds an attachment circuit to a pseudowire to configure 
an AToM static pseudowire, specifies MPLS as the 
tunneling method, and enters the xconnect configuration 
mode.

Содержание ASR1002 - ASR 1002 Router















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды