manualshive.com logo in svg

Cisco ASR1002 - ASR 1002 Router, Руководство по настройке программного обеспечения

Поделиться
Скачать
Cisco ASR1002 - ASR 1002 Router Скачать руководство пользователя страница 391

 

      Configuring MPLS Layer 2 VPNs

  Configuring Frame Relay DLCI-to-ATM AAL5SNAP Bridged Interworking

15

Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide

Step 23

interface serial

 slot/subslot/port:timeslot

Example:

Router(config)# 

interface Serial

0/3/0:0

Specifies a serial interface created on a channelized 
T1 controller.

Step 24

no ip address

Example:

Router(config-if)# 

no ip address

Removes the previously configured IP address.

Step 25

encapsulation frame-relay

Example:

Router(config-if)# 

encapsulation frame-relay

Configures the Cisco Frame Relay encapsulation on 
serial interface.

Step 26

frame-relay intf-type dce

Example:

Router(config-if)# 

frame-relay intf-type dce

Configures a Frame Relay switch type. The router 
functions as a switch connected to a router.

Step 27

frame-relay interface-dlci

 

dlci

 

switched

Example:

Router(config-if)# 

frame-relay interface-dlci

 101 

switched

Assigns a data-link connection identifier (DLCI) to 
a specified Frame Relay subinterface on the router.

Step 28

exit

Exits the interface configuration mode.

Step 29

interface GigabitEthernet 

slot/subslot/port

Example:

Router(config)# 

interface GigabitEthernet

 0/0/1

Specifies the Gigabit Ethernet interface for the 
connection of the PE routers.

Step 30

ip address 

ip-address

 

mask

Example:

Router(config-if)# 

ip address

 10.10.1.2 

255.255.255.0

Specifies the IP address for the Gigabit Ethernet 
interface.

Step 31

negotiation auto

Example:

Router(config-if)# 

negotiation auto

Enables the auto negotiation protocol to configure 
the speed, duplex, and automatic flow control of the 
Gigabit Ethernet interface.

Step 32

mpls ip

Example:

Router(config-if)# 

mpls ip

Enables MPLS forwarding of the IPv4 packets 
towards the MPLS core.

Step 33

exit

Exits the interface configuration mode.

Command or Action 

Purpose

Содержание ASR1002 - ASR 1002 Router















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды